About b.go

b.go · 12-01-2003

Hi all,I would like to use NBAR to manage LAN access to internet especially for Kazzaa or P2P softwares. Some suggestions are to use NBAR with PDLM.My router is 2651XM with 12.2(8)T, and it has ip nbar command in it. But link to Cisco page on PDLM ta...

b.go · 08-14-2003

Dear all,I want to reduce bottleneck to our ISP link (256kbps) caused by users' download, etc. Below is my configuration.interface Serial0/0 ip address rtr.ip net_mask_rtr ip access-group 100 in ip nat outside rate-limit input access-group 104 128000...

b.go · 06-23-2003

hi, i've just put my new web-server into DMZ zone and allowed only http, ftp(from internal), echo access into it. but i'm still confused between in and out ACLs. Now I am not able to update or browse from this server. They seem OK to me, since I am t...

b.go · 05-21-2003

Hi all,I have a router on stick with Cisco 2551XM & Catalyst 2950-SI to manage 2 Class C networks (192.168.1.x/24 & 192.168.2.x/24). Cisco 2651XM|Catalyst 2950 --- VLAN1 switch 192.168.1.x/24 (Catalyst 3550-SMI)|VLAN2 switch 192.168.2.x/24 (Catalyst ...

b.go · 05-12-2003

Hi all,I have following network diagram,Router1(2651XM)|switch1(2950) -- VLAN1 |VLAN2 -- router2 (pc) -- LAN3Router1 and switch1 are configured as router on a stick config (with VLAN1 & VLAN2). Another PC(acts like router2 to LAN3) is being added.A ...

b.go · 01-06-2004

hi ralf, as long as you don't disable debugging then it will keep logging. But it will be a very very big log file. I did it in the past just for only half day and it took 19 MBytes of log file :)good luck.best regards,b.go

b.go · 01-06-2004

hi ralf, maybe there is another good way to do it.But i did it just for debugging, and not logging for all day long. Add & or adjust some of these to suit your need.logging buffered 4096 debugginglogging trap debugginglogging facility local6logging ...

b.go · 12-12-2003

hi momo51,the acl no. 1 is only for defining interesting traffic to be NATed. You can apply additional acls to incoming ethernet. So the denied hosts can't be NATed since they are not allowed to enter the incoming interface.hope this will help. good ...

b.go · 12-08-2003

hi evosloo, i'm glad to hear that.You can use ACL to apply access restriction for your access between those LANs.e.g:router-config#access-list 101 permit ip 192.168.0.0 0.0.0.255 192.168.1.0 0.0.0.255 anythis should allow any kind of services from 19...

b.go · 12-03-2003

hi momo51,you can create an access-list for your internal network access-list 1 permit 192.168.0.0 255.255.255.0access-list 1 deny anyand then create nat:ip nat inside source list 1 pool yourpoolname overloadip nat pool yourpoolname isp.given.ip.add...

Member Since	‎10-24-2002 05:23 PM
Date Last Visited	‎08-18-2017 03:50 AM
Posts	23
Total Helpful Votes Received	3

User Statistics

User Activity

NBAR, PDLM, and p2p

rate-limit

ACLs

Traffic shaping

InterVLAN routing

Re: NAT and DHCP logging to a syslog server ?

Re: NAT and DHCP logging to a syslog server ?

Re: problem with my cable config

Re: C3550-24-SMI Config

Re: problem with my cable config