We have a ring of switches in the network, and from each ring node (DIST) downstream, there are one or more access switches (ACC). Each sw_DIST has the following configuration: interface vlan300ip vrf forwarding NET2ip address 172.16.X.1 255.255.255...
Forum Posts
Hi,We have two Internet circuits provided by the same ISP, and also use GRE to tunnel to an external 3rd party.We want to use ECMP to load balance traffic but have some questions.When ECMP is used with GRE, does it load balance using the tunnel inter...
my company bought Cisco switch ws-c4503e model s/n: SPE 21010011, SPE2101001A, SPE2050001s
Resolved! How to Identify Root Port in STP
in my Cisco 6509 Switch , the Spanning Tree for every VLAN shows me a separate mac address for the Designated Root Porte.x Designated root has priority 32768, address 000b.fc38.f81aBut I don't see any port on this switch that shows this mac address ...
https://www.cisco.com/c/en/us/td/docs/security/secure-firewall/management-center/device-config/720/management-center-device-config-72/interfaces-settings-ifcs-firewall.html#Cisco_Generic_Topic.dita_1778151e-e768-4581-a67d-be555f8ca57cTrying to follo...
I've implemented layer3 VPN's using VRF's and address-families. All is working well except I seem to be missing something when it comes to being able to do clears (soft or hard) on sessions within the vrf. For example, I can do a 'show ip bgp vpnv4 v...
How do I remove the platform hardware throughput crypto line?I want to know about this command on cisco1111.platform hardware throughput crypto { throughput value }no platform hardware throughput cryptoAfter I typed platform hardware throughput crypt...
Hi Can someone tell me if the AS5400 and AS5350 have interchangeable modules?The AS5400 modules are named AS54-DFC-xxxx and the AS5350 modules are named AS535-DFC-xxxx but they look identical, and many manuals/pages describe them together, however I ...
It is working on gns3Here I am working with ospfarea 0 backbone is 222 and is connected with another area 33 so router 6 is ABR between this 2 areas In the north area router R3 is working like a ASBR connecting EIgrp routing protocol and Ospf routin...
Hello,I'm trying to route traffic to a router that is not directly connected using pbr. Here is my config:Extended IP access list dsl-inet deny ip any 192.168.0.0 0.0.255.255 deny ip any 10.50.0.0 0.0.255.255 deny ip any 10.51.0.0 0.0.255.2...
Hi Team, Need some real technical Advice for the integration of Catalyst 6500 with Nexus 9000 in NX-OS operating system. I have existing Catalyst 6500 Switches running as HSRP as a Core in current Infrstructure. I am going to integrate with 2 Nexus ...
i need to reset bios admin password by Using the Clear Password Header but i don't know the location of this header to jumper it to clear the user-defined BIOS administrator password. i think it is like ucs servers can be reset by shortening pins a...
Dear all,I have to use mode conditioning cable when running GLC-LH-SM on multi-mode fibre. Does any know there is any cisco LC-SC interface mode conditioning cable? ThanksGary
My DHCP is getting filled with BAD IP ADDRESSES and I am not sure why. Looking at the VLAN config on the L3 switch the interface has both DHCP helper addresses set.. could this be causing it? how to get around it?
It's difficult to express in words how much I hate Visio, its appalling usability seems only rivalled by its ubiquity. The job demands that I use it. I have a very basic need of a stencil for a generic Switch and a Router. Cisco seemed to have made t...
