Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About neritoledano
Stats
Member since
09-24-2012
5
Posts
0
Helpful
0
Solutions
Created by
neritoledano
in Switching
in Switching
09-28-2012
07:51 AM
09-28-2012
07:51 AM
I'm trying to make an InterVLAN routing but it won't let me make it. I need interconnecting two vlans. And also i made a simulation on "cisco packet tracer" with the right commands and the intervlan routing it's working pretty good but it wouldn't work in my Small Business Cisco Router (it's already at L3 "Router mode") Can anyone could help me at this please. I attach the commands : #ip routing #vlan database #vlan 1011 #no sh #vlan database #vlan 1074 #no sh #interface vlan 1011 #ip address 192.168.10.100 255.255.255.0 #interface 1074 #ip address 10.74.180.100 255.255.255.0 #interface Fa0/1 #switchport mode access #switchport access vlan 1074 #no sh #interface Fa0/2 #switchport mode access #switchport acces vlan 1011 #no sh Thanks.
... View more
Labels:
Created by
neritoledano
in Small Business Switches
in Small Business Switches
09-25-2012
06:54 AM
09-25-2012
06:54 AM
My Switch it's already as Router, this post can be closed. Thank you so much
... View more
Created by
neritoledano
in Small Business Switches
in Small Business Switches
09-24-2012
02:17 PM
09-24-2012
02:17 PM
Well...now i am unable to access to the switch. I forgot the ip address, i pressed the reset button more than 10 seconds like says the "user's guide" : To restore the managed switch configuration to the factory default settings: 1. Disconnect the managed switch from the network or disable all DHCP servers on your network. 2. With the power on, press-and-hold the Reset button for more than 10 seconds. I am on the right subnet and mask and also i can't access to the console with the cisco cable console ! I think the switch is "halfdead" if that word exists in english. I have ethernet connection but i have no access to the switch...If theres a way to make an "hyper" hard factory reset ? Thank you again...
... View more
Created by
neritoledano
in Small Business Switches
in Small Business Switches
09-24-2012
10:58 AM
09-24-2012
10:58 AM
Adding some information, if i type at command line interface "IP ?" for a command within IP (ethernet, ROUTING, etc) ROUTING didn't shows there...i know that i have to enable routing, please someone help !
... View more
Created by
neritoledano
in Small Business Switches
in Small Business Switches
09-24-2012
10:18 AM
09-24-2012
10:18 AM
Hi everyone, my switch cisco small business SF 302-08 has the latest firmware and i want to enable the routing command but it won't let me do that. I already read the reference guide for commands, i do all this procedure: IP Routing Protocol-Independent Commands starting at 629 page, but nothing happens. I need this because i want a routing between Vlan's Regards.
... View more
Labels:
Created by
neritoledano
in Switching
09-28-2012
09-28-2012
I'm trying to make an InterVLAN routing but it won't let me make it. I
need interconnecting two vlan...
Created by
neritoledano
in Small Business Switches
09-25-2012
09-25-2012
My Switch it's already as Router, this post can be closed.Thank you so
much
Created by
neritoledano
in Small Business Switches
09-24-2012
09-24-2012
Well...now i am unable to access to the switch. I forgot the ip address,
i pressed the reset button ...
Created by
neritoledano
in Small Business Switches
09-24-2012
09-24-2012
Adding some information, if i type at command line interface "IP ?" for
a command within IP (etherne...
Created by
neritoledano
in Small Business Switches
09-24-2012
09-24-2012
Hi everyone, my switch cisco small business SF 302-08 has the latest
firmware and i want to enable t...
Public Statistics
| Date Registered | 09-24-2012 10:06 AM |
| Date Last Visited | 08-18-2017 03:54 AM |
| Total Messages Posted | 5 |
