WAP150/WAP361 should be good enough. WAP150 would be the value for money option as a power adaptor comes in the box. If you're planning to use it as a repeater using the WDS feature, 150 would be the ideal choice. For WAP361 you need to purchase adaptor / power Injector ( POE+, 30Watts) seperately. WAP361 has 4 bulit in Gig ethernet ports and one of them supports POE out-  may be useful for future expansion. Since the max power requirement for WAP150  is 9.5 watts, you should be able to use 361 as POE source for another WAP -  ( You must use POE+ class switch / Power Injector for 361 though)  Cisco power injector : SB-PWR-INJ2-xx http://www.cisco.com/c/en/us/products/collateral/wireless/small-business-300-series-wireless-access-points/datasheet-c78-736452.html ... View more

May be you can use the Work group bridge option Please refer the Cisco TAC reply on other thread "Hi, My name is Eric Moyers. I am a Network Support Engineer in the Cisco Small Business Support Center. Thank you for using the Cisco Community Post Forums. Currently the only supported configuration is with the WAP321 connecting with another WAP321 in order to use WDS. Within Work Group bridge it is possible to connect with non-cisco devices ." https://supportforums.cisco.com/discussion/11924671/wap321-wifi-extenderreapeater ... View more

Does it mean that WDS can only work with WAP121 - 321 and not WAP 121 to 121 / WAP 321 to 321 ? ... View more

You should be able to use WAP150 as a Repeater using the WDS Feature ( Wireless distribution system) The bleow mentioned doc & link is for WAP321 & 121 but the same should work for 150 as well as it supports WDS http://www.cisco.com/en/US/products/ps12237/prod_technical_reference_list.html ... View more

I would say WAP361/571 should be good enough for you. Both of them need POE+ power source. Instead of  POE switch you can use  Cisco power injector -  SB-PWR-INJ2-xx.  ... View more

I still dont understand why cisco is limiting system memory to 64MB RAM & 32 MB Flash for WAP371 when the lower model WAP150 comes with 256MB RAM & 128MB Flash Even the wireless throughput for WAP150 is far better than 371 WAP 150 - 1.2 Gbps   2x2 MIMO at 5Ghz & 2x2 MIMO at 2.4Ghz WAP 371 - 950 Mbps  3x2 MIMO at 5Ghz & 2x2 MIMO at 2.4Ghz Since the power adaptor is included in box, WAP150 seems to be a value for money model ... View more

First of all why do you need that DP? Even if there is no dial peer for incoming it should use the default dial peer ( DP0) Would you mind posting the 'sh run' here ? ... View more

How are you going to identify the phones? do they have continuous DN numbers? For eg; If you want phones from DN's 492000 to 492009 then you need to configure dial-peer voice 10 voip answer-address 49200. translation−profile incoming DN49 port 0/0/1 voice translation−rule 1 rule 1 /^000/ /800/ dial-peer voice 1 pots destination-pattern 800T port 0/0/1 Prefix 00 000.! Calls from 492000 to 492009 will route via 0/0/1 ... View more

Michael, "When they forget to dial the accesscode, the BRI-Interface with destination-pattern .T is still working " Which means you must have a route pattern in CCM to forward the calls to GW, w hen they forget to dial the accesscode Why dont you configure '0' as a prefix digit on the route pattern / route list ? Which will prefix a 0 even if the user forget to dial access code and will match with 0T dial-peer ... View more

Jack, Do you have callerID for the calls coming in via FXO port ? If yes, may be you can try a DP with answer-address dial-peer voice 1 voip translation-profile incoming Cell answer-address voice translation-rule 2 rule 1 /^(pilotnumber)$/ /(ephone dn)/ voice translation-profile Cell translate called 2 ... View more

Please check the below link - search with algeria http://www.quintum.md/support/E1_R2_Information.pdf http://ae.quintum.com/support/xplatform/r2/Algeria.htm ... View more

Please post the ccapi inout & vtsp inout debugs for a failed call. ... View more

I think you forget to read this. #Note : If hunting exceeds the number of hops that the Forward Maximum Hop Count service parameter specifies, hunting expires before the 30-minute maximum hunt timer value, and the caller receives a reorder tone. This is a service parameter in Callmanager - MAx hop is set to 12 -Default ... View more