Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About joseacruz
Stats
Member since
08-09-2012
4
Posts
0
Helpful
0
Solutions
11-16-2012
05:02 AM
Hey John, Thanks for the information, but I have tried the hw-module uplink select all command, and I'm getting an % Invalid input detected at '^' marker under uplink. I also used the ? to see what options are available after I right module, and after I right uplink. Still it does not bring the inactive ports up. Thanks for the intel -Jose
... View more
11-15-2012
04:56 PM
Hello! I'm having issues getting the ports g3/5 and g4/5 from inactive to notconnect. I have tried the hw-module uplink select all in the global configuratio, but it's not working, getting a : % Invalid input detected at '^' marker. Message every time. This what I have: Power consumed by backplane : 40 Watts Mod Ports Card Type Model Serial No. ---+-----+--------------------------------------+------------------+----------- 1 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAE152101QK 2 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAE15200382 3 6 Sup V-10GE 10GE (X2), 1000BaseX (SFP) WS-X4516-10GE JAE15120205 4 6 Sup V-10GE 10GE (X2), 1000BaseX (SFP) WS-X4516-10GE JAE150900XV 5 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAE1520026G 6 48 10/100/1000BaseT (RJ45) WS-X4548-GB-RJ45 JAE152007T9 M MAC addresses Hw Fw Sw Status --+--------------------------------+---+------------+----------------+--------- 1 4055.39a5.0120 to 4055.39a5.014f 2.6 Ok 2 6400.f1dd.2a40 to 6400.f1dd.2a6f 2.6 Ok 3 c471.feee.3940 to c471.feee.3945 5.2 12.2(31r)SGA 12.2(53)SG2 Ok 4 c471.feee.3946 to c471.feee.394b 5.2 12.2(31r)SGA 12.2(53)SG2 Ok 5 6400.f1dd.2470 to 6400.f1dd.249f 2.6 Ok 6 6400.f1dd.22f0 to 6400.f1dd.231f 2.6 Ok Mod Redundancy role Operating mode Redundancy status ----+-------------------+-------------------+---------------------------------- 3 Active Supervisor RPR Active 4 Standby Supervisor RPR Standby cold System Failures: ---------------- Power Supply: bad/off (see 'show power') GTADBHDDEISESAVGA01S11#sh int status mod 3 Port Name Status Vlan Duplex Speed Type Te3/1 Not in Use disabled 1 full 10G No X2 Te3/2 Not in Use disabled 1 full 10G No X2 Gi3/3 Uplink to 3825 GTA notconnect 10 full 1000 1000BaseSX Gi3/4 Uplink via FE Medi connected trunk full 1000 1000BaseSX Gi3/5 Uplink via FE Medi inactive 1 full 1000 1000BaseSX Gi3/6 Not in Use disabled 1 full 1000 No Gbic GTADBHDDEISESAVGA01S11#sh int status mod 4 Port Name Status Vlan Duplex Speed Type Te4/1 Not in Use disabled 1 full 10G No X2 Te4/2 Not in Use disabled 1 full 10G No X2 Gi4/3 Uplink to 3825 GTA notconnect 1110 full 1000 1000BaseSX Gi4/4 Uplink via FE Medi connected trunk full 1000 1000BaseSX Gi4/5 Uplink via FE Medi inactive 1 full 1000 1000BaseSX Gi4/6 Not in Use disabled 1 full 1000 No Gbic Any help will be gratefull. Cheers -Jose
... View more
Labels:
08-31-2012
08:49 AM
Hello To all!, I just want to thanks for all the help. All the information that you presented was very helpful. Cheers
... View more
08-09-2012
06:12 AM
Greetings All, I'm getting CRC errors on one of my serial interfaces: #sh int Serial0/0/0:1 Serial0/0/0:1 is up, line protocol is up Hardware is Serial Description: DHEC.800936.811.ATI MTU 1500 bytes, BW 1536 Kbit/sec, DLY 20000 usec, reliability 255/255, txload 1/255, rxload 21/255 Encapsulation PPP, LCP Open, multilink Open Link is a member of Multilink bundle Multilink1, loopback not set Keepalive set (10 sec) Last input 00:00:00, output 00:00:00, output hang never Last clearing of "show interface" counters 17:20:42 Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0 Queueing strategy: weighted fair [suspended, using FIFO] FIFO output queue 0/40, 0 drops 5 minute input rate 132000 bits/sec, 18 packets/sec 5 minute output rate 9000 bits/sec, 11 packets/sec 756027 packets input, 733579767 bytes, 0 no buffer Received 0 broadcasts (0 IP multicasts) 2123 runts, 0 giants, 0 throttles 2660 input errors, 532 CRC, 0 frame, 0 overrun, 0 ignored, 5 abort 508136 packets output, 77127054 bytes, 0 underruns 0 output errors, 0 collisions, 0 interface resets 0 unknown protocol drops 0 output buffer failures, 0 output buffers swapped out 0 carrier transitions Timeslot(s) Used:1-24, SCC: 0, Transmitter delay is 0 flags I have open tickets with telco and they are not seeing any problems on the ckt. Also, they mention that issue may be hardware related. Are there any troubleshooting test and I can perform on the router, to determine what may be the issue. Cheers
... View more
Labels:
11-16-2012
Hey John,Thanks for the information, but I have tried the hw-module
uplink select all command, and I...
11-15-2012
Hello!I'm having issues getting the ports g3/5 and g4/5 from inactive to
notconnect. I have tried th...
08-31-2012
Hello To all!,I just want to thanks for all the help.All the information
that you presented was very...
Public Statistics
| Date Registered | 08-09-2012 05:39 AM |
| Date Last Visited | 08-18-2017 03:55 AM |
| Total Messages Posted | 4 |
