Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Lukas Mazur
06-21-2019
Lukas Mazur
Member since
04-04-2009
Beginner
Personal Web Page : http://www.nts.at
02-11-2016
09:55 AM
Hi Walter,
a second very similar bug is also there - https://tools.cisco.com/bugsearch/bug/CSCut61527
Symptom: B200 M4 rebooted unexpectedly A deep discovery is observed from the UCSM tech-support, rather than the intended shallow discovery Conditions: Any operation that triggers a shallow discovery could transition to a deep discovery if the Serial number of the blade's MRAID12G RAID controller is blank. Even after the unexpected reboot and deep discovery, UCSM "show server inventory expand" output will show a blank SN for the MRAID12G RAID controller: RAID Controller 1: Type: SAS Vendor: Cisco Systems Inc Model: UCSB-MRAID12G Serial: HW Revision: C0 PCI Addr: 01:00.0 Raid Support: RAID0, RAID1 OOB Interface Supported: Yes Rebuild Rate: 30 Controller Status: Optimal Example operations that will trigger a shallow discovery: CIMC Reset UCS Manager Upgrade UCS Manager Cluster lead operation IOM Reboot/Reset IOM Offline Event due to cable disconnect/reconnect Fabric Interconnect Reboot
experienced your bug aswell some time ago :/ - there seem to be some stuff going on with the SAS controllers in the B200 M4 ... had some issues lately
BR Lukas
... View more
Created by
Lukas Mazur
in Unified Computing System Discussions
in Unified Computing System Discussions
04-16-2010
12:27 PM
04-16-2010
12:27 PM
hi all, can anybody explain me in detail how multicast traffic is forwarded between UCS blades? MAC adresses from on ServerPorts are learnd - those managed by the UCS wont age out. Unknown unicasts are dropped on uplink ports broadcast traffic is forwarded to all servers. regarding multicast traffic I only found the following statement: Server-to-server multicast and broadcast traffic is sent through all uplink ports in the same VLAN. but 2 Blades on UCS dont receive Multicast Traffic from eachothe - by default. any ideas regarding this issue? Thx lukas
... View more
Labels:
Created by
Lukas Mazur
in Unified Computing System Discussions
in Unified Computing System Discussions
02-19-2010
12:32 AM
02-19-2010
12:32 AM
hi all, i wanted to test the scenario that if one blade fails the service profile can simply be applied to another blade and with local disks you just have to replace the disks. And exactly here is my problem: when i replace the hdds (with ESX installed) in Raid 1 configuration and plug them into another blade, apply the service profile(of the "failed" blade) to the new blade and boot it the system is not able to boot because it does not see the LUN/Volume. have i forgotten a step?? thanks in advice for any hints. thx lukas
... View more
Labels:
Created by
Lukas Mazur
in Unified Computing System Discussions
in Unified Computing System Discussions
02-10-2010
06:41 AM
02-10-2010
06:41 AM
hi all, is it possible for Nexus5k to operate as the only SAN switch (FC) between a UCS and a FC EMC Storage with no other MDS switches used? to better clarifly my question Storage | | -------------------- ------------------- FC | | N15K N15K N15K in switch mode | | FC | | Fabric-Interconnect A F-In B UCS Blades i know that this seems like an nexus related question but i need the clarification on UCS. thanks lukas
... View more
Labels:
02-11-2016 09:55 AM
Hi Walter, a second very similar bug is also there -
https://tools.cisco.com/bugsearch/bug/CSCut6152...
04-16-2010 12:27 PM
hi all,can anybody explain me in detail how multicast traffic is
forwarded between UCS blades?MAC ad...
Created by
Lukas Mazur
in Data Center Switches
03-30-2010 01:38 AM
03-30-2010 01:38 AM
hi Naren,i experienced the issue again ... ( 2 weeks everything was
ok)here's the output of sh svs n...
Created by
Lukas Mazur
in Data Center Switches
03-25-2010 03:29 AM
03-25-2010 03:29 AM
hi Naren,subgroups are a great advice for this situation.i would still
prefer to use mac-pinning for...
Created by
Lukas Mazur
in Data Center Switches
03-23-2010 08:48 AM
03-23-2010 08:48 AM
hi all,i've been thinking about some common deployments of vSphere 4 and
N1kv on UCS Systems.Usually...
03-14-2010 03:23 PM
hi ryan,since version 1(2) VMotion of VSM VMs is supported and therefore
the placement of VSMs in a ...
Created by
Lukas Mazur
in Data Center Switches
03-08-2010 03:04 AM
03-08-2010 03:04 AM
hi all,i've got a weird behavior on one of mine ESX hosts.when i execute
a show command related to a...
03-07-2010 10:58 PM
hi Robert, Naren,i had time to test the config once again and
experienced no troubles enabling the h...
03-07-2010 10:54 PM
hi Jason, Robert,i observed a similar behavior on my ESX servers. The
Problem was that immediatelly ...
03-02-2010 11:46 PM
hi Robert,i'll gonna test it once again with my release (1.1(1j) not
1.1.1e - sorry for the mistake)...
03-02-2010 01:58 PM
hi all,this week i have tested the deployment of a N1kv on our UCS test
system.Everything worked fin...
Created by
Lukas Mazur
in Unified Computing System Discussions
02-19-2010 12:32 AM
02-19-2010 12:32 AM
hi all,i wanted to test the scenario that if one blade fails the service
profile can simply be appli...
Created by
Lukas Mazur
in Unified Computing System Discussions
02-10-2010 06:41 AM
02-10-2010 06:41 AM
hi all,is it possible for Nexus5k to operate as the only SAN switch (FC)
between a UCS and a FC EMC ...
Created by
Lukas Mazur
in Data Center Switches
01-27-2010 12:08 PM
01-27-2010 12:08 PM
hi,we were running the latest release of nexus1000v 4.0(4)SV1(2) and ESX
4 Update 1 on all Hosts. Th...
Created by
Lukas Mazur
in Data Center Switches
01-27-2010 07:03 AM
01-27-2010 07:03 AM
hi Jens,yes the password is set in the first phase (ova deployment) -
but atleast in my case the pas...
Public Statistics
| Date Registered | 04-04-2009 01:23 AM |
| Date Last Visited | 06-21-2019 01:02 AM |
| Total Messages Posted | 24 |
| Total Helpful Votes Received | 2 |
