Hi, We have a new deployment of 2x C220M6 servers, standalone mode, both with UCSC-PCIE-C25Q-04 adapters installed, but when logging into the CIMC GUI and clicking into these, we get the following error message: Unable to communicate with Card (actio...
I knew the C240M4 is not officially support them on the list, but just wonder with the firmware version C240M4.4.1.2f.0.1024230116, is it possible to run with any new (comparing to the official list) version of GPUs, e.g. v1000, A5000?
I am trying to relocate one of the Chassis(2) and subordinate FI to different rack in same location without downtime. ENVIRONMENT: FI model: 6200 (EOS) Chassis Model: UCSB-5108-AC2 2 FI's connected to 2 chassis (blade servers) with high availability ...
Hi everyone,I have a Cisco C220 M4 server with the following firmware versions:BIOS: C220M4.3.0.4c.0.0502191259CIMC: 4.1(2m)The issue I'm facing is that the fans are spinning at extremely high speeds, generating excessive noise, although they are rep...
Hi Everyone,I have a C220 M4 that was previously connected to UCS and is now being used as a standalone server.CIMC is configured and accessible via KVM. Two Ethernet cables are connected and show up in CIMC under External Interfaces.However, the OS ...
I have apic on UCS C220 M5 Rack Servers. I update CIMC and other components using HUU to version 4.2.2a. After update CIMC GUI is not responding. I can ssh to CIMC ip address and the apic is seen in aci fabric as Fully fit. I have rebooted cimc, disa...
Hi all,I'm deploying two new UCS-X Direct chassis with X210 blades, they are air gapped so will not be connected to Intersight and will just be configured using UCS Manager.I'm trying to build the service profile for the x210 blade but can't seem to ...
Hi Team, There is a requirement to downgrade the blade firmware from 4.2(3) to 4.1.3h, and subsequently to 3.1, in order to match the UCS Infrastructure version. As this involves a blade server, I would like to clarify: will all the servers be downgr...
Hi Team,There is a requirement to downgrade the blade firmware from 4.2(3) to 4.1.3h, and subsequently to 3.1, in order to match the UCS Infrastructure version.As this involves a blade server, I would like to clarify: will all the servers be downgrad...
Hello all,My first post on this forum so forgive me if I've not pitched it at the correct technical level.I was having trouble working with vMedia, specifically mounting an ISO image from an HTTP server. Frustratingly, this had worked last week. Afte...
Hello Everyone,I need to remotely shut down and power on a Cisco UCSC-C240-M5S server. I’m familiar with performing this task on Dell servers via iDRAC, but I'm not experienced with Cisco UCS.I’d like to confirm:If I shut down this server remotely, w...
Does anyone know if the requirement for 2 CPU population on a C220-M5 has been lifted for Optane DCPMMs? I would like to add two 128GB Optane DCPMMs to my existing 1 CPU config.
Hi All, I have checked UCSX install GPU Card, I knowvthere are two types of installations GPU One type of architecture is direct installation Nvidia L4 GPU on X210C , but it needs to be install X10c Front Mezzanine GPU Module , another type is PCIE N...
Hello Everyone,I am receiving the following error on Cisco UCS Manager, <faultInstack="yes"cause="health-led-amber-blinking"changeSet=""code="F1236"created="2023-06-13T21:20:13Z"descr="sys/rack-unit-4/health-led shows error. Reason DDR4_P1_A1_ECC:Sen...
Hello.I have two old Cisco u200 M2 stand-alone servers that I wanted to revive to use in a lab environment. But I thought it would be a good idea to first update BIOS and firmware.So I downloaded ucs-c200-huu-1.4.3z09.iso, that seems to be the latest...
