Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About brasso_42
Stats
Member since
07-31-2012
10
Posts
0
Helpful
0
Solutions
01-14-2013
10:07 AM
Hi I have a cisco 1841, Im trying to write an app which will get the Interface Utilization on my 2 atm interfaces and fast eth 0/0 interface. I’ve been reading up and have got as far as downloading the codeplex snmp library project. I’m using the snmpget app to get details off my 1841 successfully, but I now need to know the OID for interface utilization and how to define which interface to get. I’ve tried reading round but am lost in a crazy world of mibs and feel like I’m looking for a needle in a haystack! Can any one help Thanks SiBrasso
... View more
Labels:
11-29-2012
04:34 AM
Hi Can any one point me to a list of Protocol Number with their name and descriptions for use in extended ACLs In particular I want to deny CDP, but a full list would be very useful for future reference. Many thanks Si
... View more
Labels:
11-28-2012
05:51 AM
Hi I have a VRF which has 3 directly connected networks. Each network can route to each other, however I want X to route to Y and Z to route to Y. How can I stop X routing to Z? Thanks Si
... View more
Labels:
08-29-2012
04:06 AM
Hi I’m having an issue with one of my lines in an MLPPP bundle and need to separate it out for further testing. To do this I’ve created another Dialer and re-assigned the atm interface (atm0/0/0) to it. Then I’ve done a shut and then a no shut a min or two later. To my surprise the debug ppp negotiation showed the user name from Dialer1 and then the line was back in my multi link bundle. Can any one spot where I’m going wrong this is driving me mad. My relevant Config is below: interface ATM0/0/0 no ip address no atm ilmi-keepalive dsl operating-mode auto pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 2 ! ! interface ATM0/1/0 no ip address no atm ilmi-keepalive dsl operating-mode auto pvc 0/38 encapsulation aal5mux ppp dialer dialer pool-member 1 ! ! interface Dialer0 ip address negotiated ip virtual-reassembly encapsulation ppp dialer pool 1 keepalive 1 ppp reliable-link ppp authentication chap callin ppp chap hostname my_normal@user ppp chap password 0 psw ppp multilink ! interface Dialer42 ip address negotiated ip virtual-reassembly encapsulation ppp dialer pool 2 ppp reliable-link ppp authentication chap callin ppp chap hostname my_testing@user ppp chap password 0 psw !
... View more
Labels:
08-21-2012
06:40 AM
Hi Cadet thanks for the pointer on this, Tracking wont work with interface, but I asked the IPS to add another loopback interface which I could use as a next hop address in our VRF. I then used an ACL on the Dialer1 interface to deny access to it through there so all trafic would be forced through Dialer2 as this is the only route the next hop is avalable and when Dialer 2 goes down the next hop is removed and the trafic goes through Dialer1. This only works with upload though. I needed down routes adding via RADIUS Cisco-AVPair to get the download to work as well. All one now though, Thanks again!
... View more
08-20-2012
07:58 AM
Hi This works if I do a “shut” on Dialer2, but if I unplug the phone line it doesn’t. If I do a “show ip int br” it shows Dailer2 as up. Is there any way I can show this as down when its not connected or should I not be using a Dialer interface to do this? Thanks
... View more
08-20-2012
07:22 AM
Hi This works for routing traffic when Dialer2 is up, but when its down the traffic is not routed to Dialer1 Any ideas how to make it fail over? Many thanks for your help.
... View more
08-20-2012
06:31 AM
Hi I have 2 Dialer interfaces, I want to route IP from LAN ip 10.5.200.1 to any via Dialer2 unless it goes down. The Dialer’s are DSL connections and the next hop is the same for both connections. Any ideas how I can do this? Thanks
... View more
Labels:
07-31-2012
06:30 AM
Hi Thanks for the answer, but ADSL2+ should support legacy devices and thus the WIC-1ADSL should be stable. They do work and they do get good throughput its just the disconnect every so often. I’ll do some more digging.
... View more
07-31-2012
05:49 AM
Hi I’m testing a 1841 with 2 WIC-1ADSL cards, but the connections are dropping every 30-50mins. If I swap the cars out for HWIC-1ADSL’s then the lines are stable. I’ve had the profiles on the lines dropped the 4mb down and 512k up but I’m still getting the same issue. I’ve tried a few 1841’s with various IOS’s and different WIC’s but still get the same result. Has any one seen this before or know how I can go about trouble shooting it? Thanks Brasso
... View more
Labels:
01-14-2013
HiI have a cisco 1841, Im trying to write an app which will get the
Interface Utilization on my 2 at...
11-29-2012
HiCan any one point me to a list of Protocol Number with their name and
descriptions for use in exte...
11-28-2012
Hi I have a VRF which has 3 directly connected networks. Each network
can route to each other, howev...
08-29-2012
HiI’m having an issue with one of my lines in an MLPPP bundle and need
to separate it out for furthe...
08-21-2012
Hi Cadetthanks for the pointer on this, Tracking wont work with
interface, but I asked the IPS to ad...
08-20-2012
HiThis works if I do a “shut” on Dialer2, but if I unplug the phone line
it doesn’t. If I do a “show...
08-20-2012
HiThis works for routing traffic when Dialer2 is up, but when its down
the traffic is not routed to ...
08-20-2012
HiI have 2 Dialer interfaces, I want to route IP from LAN ip 10.5.200.1
to any via Dialer2 unless it...
07-31-2012
HiThanks for the answer, but ADSL2+ should support legacy devices and
thus the WIC-1ADSL should be s...
Public Statistics
| Date Registered | 07-31-2012 05:32 AM |
| Date Last Visited | 08-18-2017 03:56 AM |
| Total Messages Posted | 10 |
