About nenduri

nenduri · ‎08-22-2011

Simon, Can you please send the output of the following commands on VEM? vemcmd show pc vemcmd show pinning vemcmd show l2 vemcmd show l2-emergency-aging-stats thanks, Naren

nenduri · 03-25-2013 11:18 AM

Hi Chris,You need to enable segmentation feature to use segment bridge domains. Please use "feature ...

nenduri · 08-22-2011 02:59 PM

Simon,Can you please send the output of the following commands on VEM?vemcmd show pcvemcmd show pinn...

nenduri · 05-21-2010 12:20 PM

The 'system mtu' command is for uplink port profile that has system vlans. Once you have this config...

nenduri · 05-05-2010 04:21 PM

This can happen if the upstream switches are not L2 connected on control VLAN. Can you please check ...

nenduri · 04-01-2010 10:36 AM

Hi Lukas,The issue is two modules (in your case it is module 6 and module 4) having the same MAC add...

nenduri · 03-26-2010 11:18 AM

Hi Ryan,Can you send the output of the following commands?vemcmd show trunkvemcmd show portvemcmd sh...

nenduri · 03-25-2010 03:24 PM

Hi Ryan,The pinning of iscsi multipath capable ports is completely orthogonal to vPC-HM pinning. vPC...

nenduri · 03-24-2010 07:47 PM

Lukas,Can you send the output of the following command on VSM?show svs neighborsthanks,Naren

nenduri · 03-23-2010 12:28 PM

Patrick,Per your message below, as you have stacked 3750s, which is a clustered switch. right?If it ...

nenduri · 03-23-2010 12:09 PM

Hi Lukas,Let's consider the example you mentioned below,vmnic0 and vmnic1 using Profile A which will...

nenduri · 03-09-2010 02:55 PM

It is nothing to do with port channels. Ports will get added to port channels when they come up. In ...

nenduri · 03-03-2010 10:28 PM

Lukas,It is recommended to disable the "fabric failover" on UCS. If you enable fabric failover on UC...

nenduri · 03-01-2010 09:42 AM

Is the VSM booting from local disk? or from a central storage?You should see only one static entry f...

nenduri · 02-22-2010 04:01 PM

when you configure the vPC-HM with "sub-group cdp" the port will be kept down until the CDP informat...

nenduri · 02-08-2010 01:31 PM

Can you send the running configuration of the three ports on each 6500?Regarding the drop count, do ...

Date Registered	‎01-21-2009 03:20 PM
Date Last Visited	‎05-17-2018 01:52 AM
Total Messages Posted	34
Total Helpful Votes Received	3

Re: Problem with MAC Pinning and new VL...

Re: VXLAN 1000v

Re: Problem with MAC Pinning and new VLAN

Re: "system mtu" command in SV1(3)

Re: VSM and VEM's losing connectivity

Re: delayed show command output with error code

Re: Appropriate way to pin to manual sub-group with mac-pinning?

Re: Appropriate way to pin to manual sub-group with mac-pinning?

Re: delayed show command output with error code

Re: Moving VSM Guest to VEM host

Re: Best Practice / Traffic Flows running N1kv on UCS (with Palo)

Re: Port-Channels not coming up until VSM reloaded

Re: N1kv on UCS (MenloQ)

Re: Nexus1000v Management stuck in lveth Port

Re: Interface stays in link-up State (vPC)

Re: Dropping Packets on Physical Uplinksk