Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About Pari Thiagasundaram
09-25-2018
Stats
Member since
08-25-2005
226
Posts
170
Helpful
26
Solutions
Created by
Pari Thiagasundaram
in Network Management
in Network Management
08-10-2017
08:41 AM
08-10-2017
08:41 AM
Open the shell prompt on the PI Server.
telnet smtp-server-ip 25
Do you see a response?
... View more
Created by
Pari Thiagasundaram
in Network Management
in Network Management
07-27-2017
03:57 PM
07-27-2017
03:57 PM
I dont have a PI to test. Did you try:
root_disable
root_enable
... View more
Created by
Pari Thiagasundaram
in Network Management
in Network Management
07-18-2017
08:39 AM
07-18-2017
08:39 AM
- Open a putty session and enable logging to capture all outputs.
- SSH to your WLC.
- Run the command "show ap inventory all"
- Exit out of the SSH Session.
- Open the text file and search for the serial number.
... View more
Created by
Pari Thiagasundaram
in Network Management
in Network Management
05-31-2017
08:48 AM
05-31-2017
08:48 AM
I suggest that you upgrade the PI code to the latest one as well.
... View more
Created by
Pari Thiagasundaram
in Network Management
in Network Management
05-25-2017
09:08 AM
05-25-2017
09:08 AM
Brett, you will see issues with those numbers.
... View more
Created by
Pari Thiagasundaram
in Network Management
in Network Management
05-23-2017
08:58 AM
05-23-2017
08:58 AM
Open a TAC Case and have the engineer assign an enhancement bug to your SR. By this way, the Business Unit can track the number of users requesting this device to be added to the next DP. They would prioritize.
... View more
Created by
Pari Thiagasundaram
in Network Management
in Network Management
05-23-2017
05:53 AM
05-23-2017
05:53 AM
The message type is incorrect. It should be something like: (Just an example, so test it with the message type that you want in your live environment.)
%SW_MATM-4-MACFLAP_NOTIF
... View more
05-22-2017
03:44 PM
There isnt any difference between a VM and a physical. If you have followed the specs listed in the release notes, you should be fine. I dont remember the script that is used to check the disk IO speed. If you open a TAC case they should be able to give you one. The Disk IO speed should be greater than a specified number.
Did you try to do a fresh install of PI and restore maps from backup and see if that resolved the performance issue you had?
... View more
Created by
Pari Thiagasundaram
in Network Management
in Network Management
05-18-2017
01:11 PM
05-18-2017
01:11 PM
Line 1369 onwards on this xls file that you can download from Cisco Prime. Not sure if it is updated for this device.
http://www.cisco.com/c/en/us/support/cloud-systems-management/prime-infrastructure/products-device-support-tables-list.html
... View more
Created by
Pari Thiagasundaram
in Network Management
in Network Management
05-18-2017
12:38 PM
05-18-2017
12:38 PM
Dan, it would depend on the exact "flavor" of your N9K that you have. I would suggest you just run a snmpwalk against your switch which is a much faster and more "accurate" result.
Syntax:
snmpwalk -v 2c -c community-name-goes-here ip-address-goes-here sysobjectid
... View more
05-17-2017
07:29 PM
You will have to clear the java cache. Control panel > java >java tab
... View more
Created by
Pari Thiagasundaram
in Network Management
in Network Management
05-15-2017
08:44 AM
05-15-2017
08:44 AM
If you hover your mouse next to the "Partial authentication error", it will tell you the reason why it went to that state.
You would need to tell me what the error about NCS repository is. Is the HDD getting full ? Try doing a NCS Cleanup or deleting your older backups from that folder. Always, it is a good idea to have the NCS repository point to a FTP Server and NOT take the backups locally on the server.
... View more
Created by
Pari Thiagasundaram
in Network Management
in Network Management
05-11-2017
07:48 AM
05-11-2017
07:48 AM
You can automate that with EEM script.
... View more
05-10-2017
01:38 PM
1) You may want to see if your alarm configurations are intact after your upgrade.
2) Enable debugs, re-produce the issue, download the debugs and take a look at it to see whats going on. Look at the ncs-0-0.log in particular.
... View more
Created by
Pari Thiagasundaram
in Network Management
in Network Management
05-10-2017
01:24 PM
05-10-2017
01:24 PM
On good ole Cisco routers you can do the "snmp-server view" command and restrict all kinds of OID's. This aint gonna happen on the NX-OS.
So tell us the "why", you want to do the snmpset for ifAdminStatus. I am trying to think of other solutions if that may help
... View more
07-18-2017
- Open a putty session and enable logging to capture all outputs. - SSH
to your WLC. - Run the comma...
05-23-2017
Open a TAC Case and have the engineer assign an enhancement bug to your
SR. By this way, the Busines...
05-23-2017
The message type is incorrect. It should be something like: (Just an
example, so test it with the me...
05-22-2017
There isnt any difference between a VM and a physical. If you have
followed the specs listed in the ...
05-18-2017
Line 1369 onwards on this xls file that you can download from Cisco
Prime. Not sure if it is updated...
05-18-2017
Dan, it would depend on the exact "flavor" of your N9K that you have. I
would suggest you just run a...
05-15-2017
If you hover your mouse next to the "Partial authentication error", it
will tell you the reason why ...
05-10-2017
1) You may want to see if your alarm configurations are intact after
your upgrade. 2) Enable debugs,...
Public Statistics
| Date Registered | 08-25-2005 09:30 AM |
| Date Last Visited | 09-25-2018 01:37 PM |
| Total Messages Posted | 226 |
| Total Helpful Votes Received | 170 |
Helpful Votes From
.jpg "Hall of Fame Cisco Employee"){kind=icon}
