Cisco Community
English
Register
Register
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Syed Taukir
‎04-09-2018

Beginner
Recent Badges
Awards
Recent Badges
See all
30 Helpful Vote
1 Accepted Solution
5 Accepted Solution
20 Replies
10 Replies
5 Replies
10 Helpful Vote
1 Helpful Vote
Stats
Member since ‎09-23-2012
25
Posts
35
Helpful
6
Solutions

Hi Phil,

Created by in Network Security
11-24-2016
11-24-2016
Hi Phil, If you can reproduce the problem then I think its worth to open a Cisco TAC case. /Syed

Since you have IP Sla, ISP-2

Created by in Network Security
02-04-2016
02-04-2016
Since you have IP Sla, ISP-2 would kick in once ISP-1 goes down and all new requests would resolve t...

You can see the backup

Created by in Network Security
02-03-2016
02-03-2016
You can see the backup default route with "show run | in route". As you have IP Sla, you would have ...

Hi Dean,

Created by in Network Security
02-03-2016
02-03-2016
Hi Dean, You can create another object network with the same host. =>From the link Configuring objec...

I've used TFTPd32 as tftp

Created by in Network Security
02-02-2016
02-02-2016
I've used TFTPd32 as tftp server and when the image has been transferred, i have only seen the outpu...

Access-list sql permit tcp

Created by in Network Security
02-02-2016
02-02-2016
Access-list sql permit tcp any any eq 1433 Access-list sql permit tcp any any eq 51146 Class-map mss...

You may check the release

Created by in Network Security
02-02-2016
02-02-2016
You may check the release notes for 9.5.X. You may go to the section "Upgrading the Software". Since...

This document should be very

Created by in Network Security
02-02-2016
02-02-2016
This document should be very helpful. IP Sla and using backup routes http://www.cisco.com/c/en/us/su...

Hi

Created by in Network Security
02-01-2016
02-01-2016
Hi Can you go to the non-working config and take packet trace packet-tracer input outside tcp 1.1.1....

The port-channel 1 is layer-3

Created by in Network Security
02-01-2016
02-01-2016
The port-channel 1 is layer-3 On the switch, under the interface port-channel, give no switchport co...

For Static NAT, you may

Created by in Network Security
02-01-2016
02-01-2016
For Static NAT, you may follow the document on how to configure. See under column 8.3 https://suppor...

You can restrict the traffic

Created by in Network Security
01-31-2016
01-31-2016
You can restrict the traffic at the Source with an ACL at either the L2 switch or L3 switch.

Hi

Created by in Network Security
01-30-2016
01-30-2016
Hi Check the packet-tracer output for 80 and 443 packet-tracer input inside tcp 1.1.1.1 12345 80 de...

As soon as you have the

Created by in Network Security
01-30-2016
01-30-2016
As soon as you have the failover configuration on the primary unit and the failover configuration on...

Hi

Created by in Network Security
01-29-2016
01-29-2016
Hi Do not use port range in a object when using dynamic PAT. The source port has to be ANY. To contr...
Public Statistics
Date Registered ‎09-23-2012 04:18 AM
Date Last Visited ‎04-09-2018 06:45 AM
Total Messages Posted 25
Total Helpful Votes Received 35
Helpful Votes From