I haven't tried removing the ACl yet as i need a CR for that, but it is something i have in mind to do.
GigabitEthernet0/0/0.240 - Group 1 (version 2) State is Active 4 state changes, last state change 1d22h Virtual IP address is 10.102.67.1 Active virtual MAC address is 0000.0c9f.f001 (MAC In Use) Local virtual MAC address is 0000.0c9f.f001 (v2 default) Hello time 3 sec, hold time 10 sec Next hello sent in 0.032 secs Authentication MD5, key-string, timeout 30 secs Preemption enabled Active router is local Standby router is unknown Priority 110 (configured 110) Group name is "hsrp-Gi0/0/0.240-1" (default)
GigabitEthernet0/0/0.240 - Group 1 (version 2) State is Standby 26 state changes, last state change 00:00:02 Virtual IP address is 10.102.67.1 Active virtual MAC address is 0000.0c9f.f001 (MAC Not In Use) Local virtual MAC address is 0000.0c9f.f001 (v2 default) Hello time 3 sec, hold time 10 sec Next hello sent in 0.496 secs Authentication MD5, key-string, timeout 30 secs Preemption enabled Active router is 10.102.67.2, priority 110 (expires in 10.928 sec) MAC address is 00f2.8b7c.6240 Standby router is local Priority 100 (default 100) Group name is "hsrp-Gi0/0/0.240-1" (default)
... View more
I have several vlans configured on two routers as sub-interfaces for each of my vlans. I'm able to ping sub-interface IP just fine between both routers except one vlan 240. If i shut the Vlan 240 down on router 2 i have no communication problems and users are able to connect on that Vlan, as soon i bring up that sub-interface on router 2 users are not able to connect on their devices in that Vlan and i cannot ping router 1 or router 2 sub-interface IP on Vlan 240.
I have HSRP configured on my vlans and i cannot even ping the standby IP on either gateway for Vlan 240 when the sub-interface is up.
Any suggestion would be appreciated.
... View more
Hello everyone, I have a simple setup with a 2611XM router and a 2950 Switch and Im trying to setup my router on the internet, but im having some difficulties. So far i get the right IP address on one of my PC connected from the DHCP pool in the router but im not able to get out to the internet. The PC is connected to port fa0/0 on the switch and port fa0/24 is trunking. Any help is much appreciated. Thanks in advance. no aaa new-model no network-clock-participate slot 1 no network-clock-participate wic 0 ip cef ! ! no ip dhcp use vrf connected ip dhcp excluded-address 10.10.2.1 ! ip dhcp pool Home_LAN import all network 10.10.2.0 255.255.255.0 default-router 10.10.2.1 dns-server 22.214.171.124 126.96.36.199 ! !multilink bundle-name authenticated ! ! ! ! ! username admin secret 5 $1$aSZN$zFs3M/9IzfOxM.ETc/BpS. archive log config hidekeys ! ! ! ! ! interface FastEthernet0/0 description WAN ip address dhcp ip nat outside ip virtual-reassembly duplex auto speed auto ! interface Serial0/0 no ip address shutdown ! interface FastEthernet0/1 description LAN no ip address ip nat inside ip virtual-reassembly duplex auto speed auto ! interface FastEthernet0/1.5 encapsulation dot1Q 5 native ip address 10.10.1.1 255.255.255.0 ! interface FastEthernet0/1.10 encapsulation dot1Q 10 ip address 10.10.2.1 255.255.255.0 ! interface Serial0/1 no ip address shutdown ! ip forward-protocol nd ! no ip http server no ip http secure-server ip nat inside source list 101 interface FastEthernet0/0 overload ! access-list 101 permit ip 10.10.2.0 255.255.255.0 any ! end
... View more