Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About phibertron
Stats
Member since
08-15-2014
63
Posts
5
Helpful
5
Solutions
02-04-2016
01:24 PM
About the only possible SOHO grade L3 Switch I came across that does what we want Cisco to do is from HP.
For what its worth, Take a look at this model HP 1910-8G
I haven't actually played with one, but from reading the admin guides,
it "appears" to support routing for IPv6.
... View more
12-08-2014
07:41 PM
your pics don't show, but I think I know what you mean take a look at this thread, it should be what your looking for SG300-10 on 1.3.7.18 Firmware has Double-Login On SSH https://supportforums.cisco.com/discussion/12296596/sg300-10-13718-firmware-has-double-login-ssh it refers to this pdf on page 470 http://www.cisco.com/c/dam/en/us/td/docs/switches/lan/csbms/sf30x_sg30x/administration_guide/78-19308-01.pdf SSH User Authentication Use the SSH User Authentication page to enable SSH user authentication by public key and/or password, and (when using authentication by public key) to add an SSH client user that will be used to create an SSH session in an external SSH application (like PuTTY). Before you can add a user, you must generate an RSA or DSA key for the user in the external SSH key generation/client application (such as PuTTY). Automatic Login If you use the SSH User Authentication page to create an SSH username for a user who is already configured in the local user database. You can prevent additional authentication by configuring the Automatic Login feature, which works as follows: • Enabled—If a user is defined in the local database, and this user passed SSH Authentication using a public-key, the authentication by the local database username and password is skipped. NOTE The configured authentication method for this specific management method (console, Telnet, SSH and so on) must be Local (i.e. not RADIUS or TACACS+). See Management Access Method for more details). • Not Enabled—After successful authentication by SSH public key, even if the username is configured in the local user database, the user is authenticated again, as per the configured authentication methods, configured on the Management Access Authentication page.
... View more
12-08-2014
03:16 PM
can the esx hosts ping your pc? are the esx hosts gateways correct? how is the vswitch on the esx hosts setup?
... View more
12-08-2014
10:26 AM
" Worth Mentioning as its not on the drawing i did but the office pc has additional ip addresses 192.168.1.200 & 10.0.0.200" what does the route table on the office pc show?
... View more
12-08-2014
08:12 AM
Your Welcome, glad to see you made progress Can you not still ping into the 10.0.0.0 network?
... View more
12-07-2014
08:59 PM
On the router do you have routes back to the networks on the switch? For Example: ip 10.0.0.0 sm 255.255.255.0 gw 192.168.0.102 ip 192.168.1.0 sm 255.255.255.0 gw 192.168.0.102 And I'll assume that you have a default route on the switch to the router? For Example: ip 0.0.0.0 sm 0.0.0.0 gw 192.168.0.1
... View more
12-07-2014
11:27 AM
The first thing that comes to mind when looking at your drawing is the potential for the this problem, The problems with asynchronous routing take a look at this, http://networkguy.de/?p=409 Worth Mentioning as its not on the drawing i did but the office pc has additional ip addresses 192.168.1.200 & 10.0.0.200 If your ping issues that your are seeing are being seen on the office pc it is most likely because it cannot access 192.168.1.0 or the 10.0.0.0 networks as from the drawing, those vlans are most likely not trunked between the switch and router and the router would also have to be vlan aware to do this and the pc would also have to have nic that do do tagging as an example of a good setup take a look at my last post with pictures in this thread https://supportforums.cisco.com/discussion/12359971/no-internet-sg300-and-rv320
... View more
12-03-2014
03:13 PM
Here is an example layout of what I would do in your scenario note: in the below diagram sg300 port 10 is connected to any lan port on the rv320 Here is the port assignment on the RV320 Note: you will need to add routes for .104 and .105 to the switch as shown in the diagram above Here is the port assignment on the SG300 note: I didn't use your config for ports assignment, mine is just an example also you will need to add a default route to the router as shown in the diagram above In regards to use general, access or trunk mode on a port if only single physical devices are going to be connected to them, then it wont matter since everything is going to be untagged, and we are only using one vlan per port Here are the SG300 DHCP pool configurations
... View more
11-29-2014
07:56 AM
I over analyzed that question Simply put, that is the IP assigned to NAT
... View more
11-29-2014
07:45 AM
Based on the hardware and os running on the router I'd say that it is normal / expected behavior Meaning that the lan ports are not separate routing interfaces and are connected to an internal switch which is connected to a single eth port on the cpu (which is normal for consumer and prosumer hardware) If I remember correctly vlan 1 is somehow hardware assigned to that eth port on the cpu
... View more
11-23-2014
07:22 PM
I don't think its possible to do that, but maybe cisco can chime in if it is possible or not
... View more
11-23-2014
02:02 PM
If you haven't already, you need to add a default gateway on the sg300 to the rv320 for example 0.0.0.0 0.0.0.0 192.168.4.60 or 192.168.5.60 having dhcp running on the switch and the router in your setup looks like a bad idea usually one would use one or the other
... View more
02-04-2016
About the only possible SOHO grade L3 Switch I came across that does
what we want Cisco to do is fro...
12-08-2014
your pics don't show, but I think I know what you meantake a look at
this thread, it should be what ...
12-08-2014
can the esx hosts ping your pc?are the esx hosts gateways correct?how is
the vswitch on the esx host...
12-08-2014
"Worth Mentioning as its not on the drawing i did but the office pc has
additional ip addresses 192....
12-08-2014
Your Welcome, glad to see you made progress Can you not still ping into
the 10.0.0.0 network?
12-07-2014
On the router do you have routes back to the networks on the switch? For
Example: ip 10.0.0.0 sm 255...
12-07-2014
The first thing that comes to mind when looking at your drawingis the
potential for the this problem...
12-03-2014
Here is an example layout of what I would do in your scenarionote:in the
below diagram sg300 port 10...
11-29-2014
Based on the hardware and os running on the routerI'd say that it is
normal / expected behaviorMeani...
11-23-2014
I don't think its possible to do that, but maybe cisco can chime in if
it is possible or not
Public Statistics
| Date Registered | 08-15-2014 12:37 PM |
| Date Last Visited | 08-18-2017 04:02 AM |
| Total Messages Posted | 63 |
| Total Helpful Votes Received | 5 |
