Need to use a SPA500DS with SPA509. are working with a UC560. what are the commands that I put in the UC560 to monitor an extension in SPA500DS buttons? ... View more

I need to integrate a SPA232D, to which they would be connecting two SPA302D with a UC560. I know through the CEC can not be done, but I guess if it can be done via CLI. Can anyone tell me the command lines necessary to do this? ... View more

Yo necesito integrar un SPA232D, al cual se estarian conectando dos SPA302D, con un UC560. Sé que a través del CCA no es posible hacerlo, pero supongo que si es posible hacerlo a través  de CLI. Puede alguien indicarme las líneas de comando necesarias para hacer esto? ... View more

I need to integrate a SPA232D, to which they would be connecting two SPA302D with a UC560.     I know through the CEC can not be done, but I guess if it can be done via CLI.     Can anyone tell me the command lines necessary to do this? ... View more

I need to integrate a SPA232D, to which they would be connecting two SPA302D with a UC560. I know through the CEC can not be done, but I guess if it can be done via CLI. Can anyone tell me the command lines necessary to do this? ... View more

I have understood that the UC320 handle up to 9 FXS. I also know that I can connect up to 2 SPA8800. but my question is: I can use a SPA8000 with the UC320? and especially from the CCA to configure it? Thank you. ... View more

have understood that the UC320 handle up to 9 FXS. I also know that I can connect up to 2 SPA8800. but my question is: I can use a SPA8000 with the UC320? and especially from the CCA to configure it? Thank you. ... View more

I have this problem: I tried to upgrade the UC540 by CCA but always failed. after several attempts, I tried to take him by the CCA to default settings and told me to first upgrade the software version UC540 (issue that could not do before). I went to the console and copy the default configuration file that was in the system directory to the startup config and did a reload. now the UC540 does not boot. I need help: - Get to boot - Take it to the default configuration - Reset the CUE Thanks to all who help. ... View more

Buenas a todos, Necesito integrar dos SPA3102 con un UC560. A cada SPA3102 le estaría conectando un teléfono análogo y una linea de la PSTN. El UC560 ya tendria ocupados ya todos su puertos FXS y FXO que trae de fabrica. El modelo exacto del UC560 es UC560-FXO-K9 Agradezco me informen que debo configurar en cada SPA3102 y que debo configurar en el UC560, bien sea por interfaz gráfica o por linea de comandos. ... View more

como fijo la hora en mis ip phone. explico: la hora actual real es (venezuela) 3:11 pm los ip phone tienen esta hora 4:11 pm adjunto el show tech del uc520 y del cue donde y que comandos debo tipear para corregir esto       ... View more

tengo dos uc520 en sitios distintos conectados a internet via DSL ya tengo para ambos sitios (UC520) configurados lo relacionado a DDNS. como hago para poder cursar llamadas entre ambos sitios? que debo configurar? oueden darme la lista de comandos? o como lo hago con el configuration assistant? uso cme 7.0 gracias ... View more

tengo un ipphone CP7940G, lo deseo configurar para que funcione como un teleworker asociado a un uc520   en el sitio donde estaría el ip phone no existe  router, sino que esta conectado directamente a internet mediante DSL   que configracion debo realizar en el ip phone y el uc520. estoy usando CME 7.0 ... View more