Hi Alexander, Thanks for your kind reply. As i noted above, in personal capacity i am in study mode going about SNMP K/W so also looking out the relevant RFCs to be thorough with. So as part of that only interested to know w.r.t IOS-XR also. Informatively we did support SNMP K/W for IOS and NX-OS at the moment and in transition to support XR also. Regards K. Lakshmi Ganesh ... View more

Hi Alexander, Thank you for your reply. Actually i was just going through the related RFCs and additionally we (HTTS-WW-NMS) are going to support SNMP K/W for XR so was just going through these. Informatively in IOS RFC 2571 was being followed for implementation of SNMP architecture. In Nexus RFC 3411 (which obsoletes RFC 2571) is being used. So was just wondering as which RFC is being followed in XR? Any idea as who can comment on this definitively? Thanks and Regards K. Lakshmi Ganesh ... View more

Hi Alexander, Just curious and want to know as based on the which RFC, SNMP architecture of IOS-XR had been adopted? Regards K. Lakshmi Ganesh ... View more

Hi, I see you are probably seeing following sort of issue. correct me if i am wrong. $ snmpwalk -v2c -c r******* 10.156.35.24 sysDescr SNMPv2-MIB::sysDescr = No more variables left in this MIB View (It is past the end of the MIB tree) $ snmpwalk -v2c -c r*******  10.156.35.24 SNMPv2-SMI::mib-2 = No more variables left in this MIB View (It is past the end of the MIB tree) So this device is not responding to ANY snmpwalk? If so, please try the following: [1] Create new SNMP community without Access list ! conf t snmp-server community ciscotac RO ! [2] then go into TCLSH from enable mode and run the below commands: *         snmp_getone ciscotac 1.3.6.1.2.1.1.1.0 *         snmp_getone ciscotac 1.3.6.1.2.1.1.2.0 For example: (please note my community string is public, you would be using ciscotac) =========== NMS-7-SW-6509#tclsh NMS-7-SW-6509(tcl)#snmp_getone public 1.3.6.1.2.1.1.2.0 { } NMS-7-SW-6509(tcl)# NMS-7-SW-6509(tcl)#snmp_getone public 1.3.6.1.2.1.1.1.0 { } NMS-7-SW-6509(tcl)# ----------------------------------------------- Remove test community string afterwards. If you don't get any output then go to [3] [3] restart the SNMP Engine. This will remove all your SNMP configuration, so please do "show run | i snmp-server"  to save a copy of the configuration before restarting SNMP Engine. ! conf t default snmp-server ! or do the following conf t no snmp-server (this will remove the snmp-server related commands) snmp-server community RO (Any one similar command saved from "show run | i snmp-server" and this will restore the snmp-server related commands and in the process restarts SNMP). [4]  If restarting doesn't work then you will need to reboot the device. * If this resolves the issue then please mark this as solution. Regards K. Lakshmi Ganesh ... View more

Hi Channa, My colleague Vinod is absolutely correct with his remark that i f you have LMS 4.0 you have to install LMS 4.2 afresh. While installing it would ask for Lic file which if you dont enter would install LMS as eval version. If you have LMS 4.0.1, you can install LMS 4.2 on top of it directly, w/o uninstall. See this segment which talks about Upgrade and Data Migration Procedure : http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/install/guide/instl.html#wp1709680 Thank you Vinod for replying it quickly. Regards K. Lakshmi Ganesh ... View more

Hi, I believe you have followed the procedures mentioned in the following links properly. http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/install/guide/instl.html#wp1709680 http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/install/guide/instl.html#wp1743797 http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/install/guide/dmg.html#wpxref77180 At this point based on the problem description what extra i can tell you is to do the following and check. 1)    Setting the properties variables in one properties file. Try this:- For LMS getting started page:  Disable the launch of Getting Start page by default (as the first page after log in). Follow the below steps:               a. Open the properties file name “gs.properties” under the path /< >/MDC/tomcat/webapps/cwlms/WEB-INF/classes/com/Cisco/nm/gs/ui               b. Update the field IS_DEFAULT_PAGE as “false”               c. Clear the browser cache and login-in(Daemon restart not required but would suggest to do the reset of casuser and daemon restart just as precautionary measure). 2) Reset the casuser and see if it resolves the issue. (This is considering the OS of the system as Windows). Procedure to reset the casuser. 1. Open a command line in the CiscoWorks server. 2. Go to the following path: NMSROOT\setup\support 3. In this path, please type as follows: resetCasuser.exe 4. Then, the next will be displayed: Please select the following option to proceed. ============================================== 1. Randomly generate casuser password. 2. Enter casuser password. 3. Exit. ============================================== Please enter a valid option: 5. Choose option 1. *** Remember to restart Daemon Manager after this: NMSROOT# net stop crmdmgtd NMSROOT# net start crmdmgtd Regards K. Lakshmi Ganesh -- If this answers your question please mark the question as "answered" and rate it, so other users can easily find it. ... View more

Hi Abdul, I believe you have followed the procedures mentioned in the following links properly. http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/install/guide/instl.html#wp1709680 http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/install/guide/instl.html#wp1743797 http://www.cisco.com/en/US/docs/net_mgmt/ciscoworks_lan_management_solution/4.2/install/guide/dmg.html#wpxref77180 At this point based on the problem description what extra i can tell you is to do the following and check. 1)    Setting the properties variables in one properties file. Try this:- For LMS getting started page:  Disable the launch of Getting Start page by default (as the first page after log in). Follow the below steps:               a. Open the properties file name “gs.properties” under the path /< >/MDC/tomcat/webapps/cwlms/WEB-INF/classes/com/Cisco/nm/gs/ui               b. Update the field IS_DEFAULT_PAGE as “false”               c. Clear the browser cache and login-in(Daemon restart not required but would suggest to do the reset of casuser and daemon restart just as precautionary measure). 2) Reset the casuser and see if it resolves the issue. (This is considering the OS of the system as Windows). Procedure to reset the casuser. 1. Open a command line in the CiscoWorks server. 2. Go to the following path: NMSROOT\setup\support 3. In this path, please type as follows: resetCasuser.exe 4. Then, the next will be displayed: Please select the following option to proceed. ============================================== 1. Randomly generate casuser password. 2. Enter casuser password. 3. Exit. ============================================== Please enter a valid option: 5. Choose option 1. *** Remember to restart Daemon Manager after this: NMSROOT# net stop crmdmgtd NMSROOT# net start crmdmgtd Then also if the issue is not getting resolved then as suggested by TAC you may need to do the configuration from scratch. Regards K. Lakshmi Ganesh -- If this answers your question please mark the question as "answered" and rate it, so other users can easily find it. ... View more

Hi, Let me know the software being used by you on this device. Give me the full image name so that i may point out the exact MIBs. Regards K. Lakshmi Ganesh ... View more

Hi, I believe the device you mentioned is the IOS based device. If it is so then you may use following MIBs depending on the version of IOS. Memory statistics via CISCO-ENHANCED-MEMPOOL-MIB and CISCO-MEMORY-POOL-MIB http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a95.shtml CPU statistics via CISCO-PROCESS-MIB and OLD-CISCO-CPU-MIB http://www.cisco.com/en/US/tech/tk648/tk362/technologies_tech_note09186a0080094a94.shtml Interface CRC via OLD-CISCO-INTERFACES-MIB (specifically "locIfInCRC"). If you want to get the interface related statistics then you have to go for IF-MIB. You may refer to following links additionally if you want help with some FAQs. http://www.cisco.com/en/US/tech/tk648/tk362/tk605/tsd_technology_support_sub-protocol_home.html http://www.cisco.com/en/US/tech/tk648/tk362/technologies_q_and_a_item09186a0080094bc0.shtml http://www.cisco.com/en/US/tech/tk648/tk362/technologies_q_and_a_item09186a00800c2612.shtml Regards K. Lakshmi Ganesh ... View more

Hi Mahmoud, Please refer to these link for details of the MIB. http://tools.cisco.com/Support/SNMP/do/BrowseOID.do?objectInput=1.3.6.1.2.1.25&submitValue=SUBMIT For the definition of the MIB http://tools.cisco.com/Support/SNMP/do/BrowseMIB.do?local=en&step=2&mibName=HOST-RESOURCES-MIB HOST-RESOURCES-TYPES http://tools.cisco.com/Support/SNMP/do/BrowseMIB.do?local=en&step=2&submitClicked=true&mibName=HOST-RESOURCES-TYPES#dependencies Regards K. Lakshmi Ganesh ... View more

Hi Mahmoud, -Host Resources MIB (RFC 1514/2790). Please refer to the RFCs noted. You may find the definitions for Host Resources MIB in the RFCs mentioned. http://tools.ietf.org/html/rfc1514 http://tools.ietf.org/html/rfc2790 Some of the useful MIBs under those which i can think of are like hrSWRunPerfTable (The table of running software performance metrics),  hrProcessorLoad (The average, over the last minute, of the percentage of time that this processor was not idle),  hrDiskStorageTable (For Disk). MIBs as below referring to both the RFCs. HOST-RESOURCES-MIB, HOST-RESOURCES-TYPES Regards K. Lakshmi Ganesh ... View more

Hi Mahmoud, Here it is important to understand that what are your business requirements (like what is that you want to monitor). Once you are able to decide that you want to monitor some particular parameters then you need to see if that is supported as per the note which i have provided to you earlier. //Quote Cisco Secure ACS 5.3 supports Simple Network Management Protocol (SNMP) to provide logging services. The SNMP agent provides read-only SNMP v1 and SNMP v2c support. The supported MIBs include: •SNMPv2-MIB •RFC1213-MIB (MIB II) •IF-MIB •IP-MIB •TCP-MIB •UDP-MIB •CISCO-CDP-MIB •ENTITY-MIB The SNMP agent is configurable on the Collection Filters page in the Monitoring and Report Viewer. //Unquote Regards K. Lakshmi Ganesh ... View more

Hi, Cisco Secure ACS 5.3 supports Simple Network Management Protocol (SNMP) to provide logging services. The SNMP agent provides read-only SNMP v1 and SNMP v2c support. The supported MIBs include: •SNMPv2-MIB •RFC1213-MIB (MIB II) •IF-MIB •IP-MIB •TCP-MIB •UDP-MIB •CISCO-CDP-MIB •ENTITY-MIB The SNMP agent is configurable on the Collection Filters page in the Monitoring and Report Viewer. Regards K. Lakshmi Ganesh ... View more