Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About David Watkins
Online
David Watkins
Enthusiast
Awards
2
Recent Badges
Stats
Member since
01-29-2013
231
Posts
59
Helpful
24
Solutions
09-21-2016
12:07 PM
IQ(Iraq) is country code -E. Your AP is -C. You must select a country code that supports the model of AP you have.
The AP and WLC must have matching regulatory domains configured.
... View more
Created by
David Watkins
in Wireless and Mobility
in Wireless and Mobility
09-21-2016
12:04 PM
09-21-2016
12:04 PM
Agreed, more detail is needed but the obvious first issue is to ensure your domains are set accordingly.
Ammar, I would suggest you collect outputs of the debugs asked above. It would also be helpful to capture the console output of the AP booting up so we can see what the AP thinks is happening.
... View more
09-21-2016
11:27 AM
Please read the regulatory compliance link I sent for that information. You should only select the country code your APs are intended to operate in. If you have the wrong AP model you need to get the correct one, not select Country Codes that are not intended for your domain.
... View more
09-21-2016
11:15 AM
Your AP is a -C domain. It's in the model type. -C-
If the AP is intended for use within GB, then you would need an AIR-LAP1142N-E-K9
operating an AP outside of its regulatory domain is not recommended as you may be violating laws and regulations.
... View more
09-21-2016
10:33 AM
If your AP is a -C domain, but your country code is -E (Great Britain), it will not join the WLC. You need to make sure you are using the appropriate regulatory domain where the Access Point will service clients.
... View more
Created by
David Watkins
in Wireless and Mobility
in Wireless and Mobility
09-21-2016
10:11 AM
09-21-2016
10:11 AM
The BSSID is derived from the Base Radio MAC(the MAC you pulled from the WLC) and is a variation created from the WLAN ID and the Radio interface used. This should get your what you're looking for.
http://www.my80211.com/home/tag/cisco-virtual-mac-address
... View more
Created by
David Watkins
in Wireless and Mobility
in Wireless and Mobility
09-21-2016
09:47 AM
09-21-2016
09:47 AM
From the Monitor Page of your WLC, look at the Access Point Join statistics. Do you have anything listed for the failure/error reason?
Based upon your information, if you select GB, you would be adding the -E regulatory domain. -C domain is for most of Asia.
http://www.cisco.com/c/en/us/products/collateral/wireless/access-points/product_data_sheet0900aecd80537b6a.html#Table280211abgnac
... View more
09-21-2016
09:41 AM
Can you post the output of your ports "run-config" and also, with AP booted up, can you post a "show mac address-table interface x/x/x"?
It would also be helpful to capture the console output of an AP booting up and post that information as well.
Thanks!
... View more
02-06-2016
12:21 PM
The question doesn't quite make sense. Is this an external WebAuth page or an internal WebAuth page? For internal, you're going to have to stick with basic HTML/CSS. If it's an external page, then you can use whatever you want, so long as you include the required data provided by Cisco in their WebAuthBundle file (ie. form/actions/script items). It would make no sense that you cannot use PHP or any other server side technologies on an "external" page because the WLC would have nothing to do with it.
... View more
02-06-2016
12:16 PM
I'm pretty sure you can't manipulate the length, but I guess I'm wondering, why on earth would you want to provide a guest user name to someone that's 24 characters long or greater?
... View more
Created by
David Watkins
in Wireless and Mobility
in Wireless and Mobility
02-06-2016
12:12 PM
02-06-2016
12:12 PM
Given it's an omnidirectional, you generally wouldn't be adjusting the elevation value since your antenna would most likely be in a standard vertical orientation. If you set the omni on it's side (not suggested) the you could use 90 degrees, etc.
With other types of antennas you may need to adjust both azimuth and elevation for downtilt and direction.
... View more
02-06-2016
12:04 PM
Cisco WLC 8.0 Configuration Guide
http://www.cisco.com/c/en/us/td/docs/wireless/controller/8-0/configuration-guide/b_cg80/b_cg80_chapter_011.html#ID307
If you're looking at the new fancy dashboard, you will find the classic menu structure via the "Advanced" link to the top-right. From there, the "Config Guide" items should all be where they are normally.
... View more
05-14-2015
03:36 PM
It means it "did" learn the IP address, however the WLC is not sending a "discovery response" to the AP's discovery request to that address.
... View more
Created by
David Watkins
in Wireless and Mobility
in Wireless and Mobility
05-14-2015
03:29 PM
05-14-2015
03:29 PM
Please read the following http://www.cisco.com/image/gif/paws/113677/virtual-wlan-dg-00.pdf You will need your AP to upgrade to at least 7.3. Also read the information regarding "hash" configuration since the vWLC utilizes an SSC, unlike the traditional hardware WLC's MIC. This is of course only relevant once you get your WLC "discovery" issues resolved.
... View more
05-14-2015
03:22 PM
Yes. You can search the community for this and find the answer very quickly. https://supportforums.cisco.com/document/94676/lightweight-autonomous https://supportforums.cisco.com/document/57476/lwapp-autonomous-conversion-and-vice-versa-access-points http://www.cisco.com/c/en/us/td/docs/wireless/controller/8-0/configuration-guide/b_cg80/b_cg80_chapter_01101010.html#topic_33BEB5AFB764448EBA1D605E5E04C049
... View more
09-21-2016
IQ(Iraq) is country code -E. Your AP is -C. You must select a country
code that supports the model o...
09-21-2016
Agreed, more detail is needed but the obvious first issue is to ensure
your domains are set accordin...
09-21-2016
Please read the regulatory compliance link I sent for that information.
You should only select the c...
09-21-2016
Your AP is a -C domain. It's in the model type. -C- If the AP is
intended for use within GB, then yo...
09-21-2016
If your AP is a -C domain, but your country code is -E (Great Britain),
it will not join the WLC. Yo...
09-21-2016
The BSSID is derived from the Base Radio MAC(the MAC you pulled from the
WLC) and is a variation cre...
09-21-2016
From the Monitor Page of your WLC, look at the Access Point Join
statistics. Do you have anything li...
09-21-2016
Can you post the output of your ports "run-config" and also, with AP
booted up, can you post a "show...
02-06-2016
The question doesn't quite make sense. Is this an external WebAuth page
or an internal WebAuth page?...
02-06-2016
I'm pretty sure you can't manipulate the length, but I guess I'm
wondering, why on earth would you w...
02-06-2016
Given it's an omnidirectional, you generally wouldn't be adjusting the
elevation value since your an...
02-06-2016
Cisco WLC 8.0 Configuration Guide
http://www.cisco.com/c/en/us/td/docs/wireless/controller/8-0/confi...
05-14-2015
It means it "did" learn the IP address, however the WLC is not sending a
"discovery response" to the...
05-14-2015
Please read the
followinghttp://www.cisco.com/image/gif/paws/113677/virtual-wlan-dg-00.pdf
You will ...
Public Statistics
| Date Registered | 01-29-2013 12:10 PM |
| Date Last Visited | 08-19-2019 09:19 AM |
| Total Messages Posted | 231 |
| Total Helpful Votes Received | 59 |
Helpful Votes From
Awards
Community Spotlight Award
Rookie April 2013
Community Spotlight Award
Doc/Video May 2013
