Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About vragotha
Stats
Member since
08-15-2006
178
Posts
82
Helpful
32
Solutions
04-02-2012
11:20 AM
You will need to install it manually http://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements/guide/cme81spc.htm https://supportforums.cisco.com/thread/2140439
... View more
Created by
vragotha
in Voice Systems
in Voice Systems
03-01-2012
11:32 AM
03-01-2012
11:32 AM
Issue a 'dir nvram:'. This will tell you if the startup config is present in there. If you want a factory default configuration, it will be available in the software pack that you can download from cisco.com
... View more
02-28-2012
10:45 AM
If your PC is on the same subnet as the UC data vlan, you should be getting a DHCP IP address in the same subnet. If that is not working, assign a 192.168.10.x/24, with 192.168.10.1 as the default gateway. This should help you connect to 10.1.10.1 You may want to start checking why DHCP isn't working - check DHCP settings on the UC, vlan and port settings on the switch you are connected to (if any).
... View more
02-27-2012
11:26 AM
Looks like your PC may not have a route to the 10.1.10.x network. Post the following - ipconfig (from the PC) show ip int brief | ex un (from the UC)
... View more
Created by
vragotha
in Voice Systems
in Voice Systems
12-20-2011
12:48 PM
12-20-2011
12:48 PM
There is a PMF available to enable Call Waiting tone. https://supportforums.cisco.com/docs/DOC-16301
... View more
12-06-2011
12:29 PM
https://supportforums.cisco.com/docs/DOC-9731 https://supportforums.cisco.com/docs/DOC-9721
... View more
Created by
vragotha
in Voice Systems
in Voice Systems
11-10-2011
01:10 PM
11-10-2011
01:10 PM
http://www.cisco.com/en/US/docs/routers/access/vg202_vg204/software/vg2_vg4_prf_ps2250_TSD_Products_Configuration_Guide_Chapter.html
... View more
11-27-2010
10:35 AM
See https://www.ciscotaccc.com/kaidara-advisor/lanswitching/showcase?case=K00835127 for an explanation Configure 'no service internal' to stop seeing those logs
... View more
11-23-2010
03:36 PM
CNA 5.6 should have support for the X series. Tentative Jan 2011.
... View more
11-15-2010
09:08 PM
Looks like an informational message. You will want to setup a sniffer to see where the what device is generating these packets. Could be a bad NIC/application that is sending out bad packets.
... View more
11-15-2010
09:03 PM
Like Colin said, stacking is not supported on 2950s. You can look into clustering - http://www.cisco.com/en/US/docs/switches/lan/catalyst2950/software/release/12.1_22_ea11x/configuration/guide/swclus.html http://www.cisco.com/en/US/docs/switches/lan/catalyst3750/software/release/12.2_55_se/configuration/guide/swclus.html
... View more
11-14-2010
01:29 AM
This switch should support bridge groups. Try configuring a bridge group and assign interfaces to each bridge group to be part of the same network. This will be similar to how vlans will work. You should also be able to configure a bvi if required
... View more
04-02-2012
You will need to install it
manuallyhttp://www.cisco.com/en/US/docs/voice_ip_comm/cucme/requirements...
03-01-2012
Issue a 'dir nvram:'. This will tell you if the startup config is
present in there. If you want a fa...
02-28-2012
If your PC is on the same subnet as the UC data vlan, you should be
getting a DHCP IP address in the...
02-27-2012
Looks like your PC may not have a route to the 10.1.10.x network. Post
the following - ipconfig (fro...
Created by
vragotha
in Voice Systems
12-20-2011
12-20-2011
There is a PMF available to enable Call Waiting
tone.https://supportforums.cisco.com/docs/DOC-16301
12-06-2011
https://supportforums.cisco.com/docs/DOC-9731https://supportforums.cisco.com/docs/DOC-9721
Created by
vragotha
in Voice Systems
11-10-2011
11-10-2011
http://www.cisco.com/en/US/docs/routers/access/vg202_vg204/software/vg2_vg4_prf_ps2250_TSD_Products_...
11-27-2010
See
https://www.ciscotaccc.com/kaidara-advisor/lanswitching/showcase?case=K00835127
for an explanati...
11-15-2010
Looks like an informational message. You will want to setup a sniffer to
see where the what device i...
11-15-2010
Like Colin said, stacking is not supported on 2950s. You can look into
clustering
-http://www.cisco....
Public Statistics
| Date Registered | 08-15-2006 03:56 PM |
| Date Last Visited | 08-18-2017 04:03 AM |
| Total Messages Posted | 178 |
| Total Helpful Votes Received | 82 |
Helpful Votes Given To
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 5 | |
| 5 | |
| 5 |
.jpg "VIP Expert"){kind=icon}
.jpg "Hall of Fame Cisco Employee"){kind=icon}
Helpful Votes From
| User | Helpful Count |
|---|---|
| 5 | |
| 5 | |
| 5 | |
| 5 | |
| 5 |
