Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About penxu
Stats
Member since
07-31-2014
18
Posts
19
Helpful
1
Solution
04-28-2017
11:24 AM
Zak, The latest analysis sounds like it is related name constraints field in certificate. I will keep you posted.
... View more
03-22-2017
10:57 AM
Hi Zak, Can you send us the latest pnp-service.log from server and "show pnp tech" from switch when you did the test?
... View more
03-21-2017
02:50 PM
Is it 2-member stack, Zak? Also, can you uncheck the "device certificate" and test again?
... View more
03-21-2017
11:13 AM
did you configure this device in project/pre-provision workflow? If so, what you see in APIC-EM side?
... View more
03-20-2017
10:51 AM
Zak, You can run this script on a Linux box to get pnp-service.log from APIC-EM. Then you can share with us. Regards, Peng
... View more
03-20-2017
09:14 AM
What is your switch code version? It seems that you only waited a little bit two and half minutes before you get into console. Can you wait a little longer for next time, say at least 6 mins? Also, what is APIC-EM version? Can you send me your APIC-EM server certificate on APIC-EM?
... View more
03-16-2017
02:42 PM
hmm, it does not look like it started pnp process at all. Are you sure that you clear the device and everything?
... View more
03-15-2017
10:30 AM
I know you tested with project rule. can you test it with "unclaimed" work flow? It seems to be that IE3000 is stuck in SUDI state.
... View more
03-15-2017
10:17 AM
Zak, Can you try with unplanned workflow? From the log, it seems device contacted to PnP sever.
... View more
03-14-2017
10:16 PM
Zak, what certificate has been installed on APIC-EM? If that certificate's issuing CA is not part of trust bundle, do not think it will work for you with port 443 as initial connection. Port 80 should work as we just install server certificate (self-signed or not) to device, then switch to HTTPs after that.
... View more
02-14-2017
08:40 PM
Sairam, I think Zak brought up a good point on version control of template. If we just keep replacing the old version, it is hard to track which device config from which version of the same template if we do not have version control. Obviously, this will be enhancement. Also need to consider if we can have a report on the number of device config generated by which template. Regards, Peng
... View more
01-31-2017
08:56 AM
Hi Stefan, Unfortunately, today the macro is hidden from users. We should add the intelligence in the future when DTP is off, if we see multiple do1q BPDUs, we should know it is statically set to trunk on uplink. Then we should set the new switch port as trunk and problem will be resolved. That is matter of how to implement and when, :-). Regards, Peng
... View more
04-28-2017
Zak,The latest analysis sounds like it is related name constraints field
in certificate. I will keep...
03-22-2017
Hi Zak,Can you send us the latest pnp-service.log from server and "show
pnp tech" from switch when y...
03-21-2017
Is it 2-member stack, Zak? Also, can you uncheck the "device
certificate" and test again?
03-21-2017
did you configure this device in project/pre-provision workflow? If so,
what you see in APIC-EM side...
03-20-2017
Zak,You can run this script on a Linux box to get pnp-service.log from
APIC-EM. Then you can share w...
03-20-2017
What is your switch code version? It seems that you only waited a little
bit two and half minutes be...
03-16-2017
hmm, it does not look like it started pnp process at all. Are you sure
that you clear the device and...
03-15-2017
I know you tested with project rule. can you test it with "unclaimed"
work flow? It seems to be that...
03-15-2017
Zak,Can you try with unplanned workflow? From the log, it seems device
contacted to PnP sever.
03-14-2017
Zak,what certificate has been installed on APIC-EM? If that
certificate's issuing CA is not part of ...
02-14-2017
Sairam,I think Zak brought up a good point on version control of
template. If we just keep replacing...
Public Statistics
| Date Registered | 07-31-2014 02:00 PM |
| Date Last Visited | 02-27-2019 01:09 PM |
| Total Messages Posted | 18 |
| Total Helpful Votes Received | 19 |
