About ekhabaro

ekhabaro · 02-24-2019

IntroductionPrerequisitesRequirementsComponents UsedConfigureNetwork DiagramConfigurationsVerification and troubleshooting Introduction This article describes how to prefer particular interface for DIA with help of vSmart data policy. Prerequisites...

ekhabaro · 02-22-2019

This article is also available on cisco.com now as well: https://www.cisco.com/c/en/us/support/docs/routers/sd-wan/214149-configure-multiple-transports-and-traffi.html IntroductionConfigurationProblemSolutionVerificationTroubleshootingReferences In...

ekhabaro · 02-22-2019

This article now available on CCO: https://www.cisco.com/c/en/us/support/docs/routers/sd-wan/214147-vedge-does-not-advertise-its-own-as-when.html IntroductionPrerequisitesRequirements Components Used Configure Network Diagram VerifyConclusionRelat...

ekhabaro · 02-22-2019

IntroductionTopology and configurationProblemSolution Introduction This article describes typical problem with a design of the redundancy when OMP path selection is enforced on a vEdge device and not on the vSmart controller that can cause to unwant...

ekhabaro · 02-22-2019

IntroductionComponents UsedConfigurevEdge router configurationCisco IOS-XE configurationVerify Introduction This article describes IPSec IKEv1 site-to-site VPN with pre-shared keys configuration in transport-vpn on vEdge between IOS device with VRF c...

ekhabaro · 10-13-2026

Configuration Group deployment uses a workflow supported by the device’s model and capabilities. In the pull workflow, Manager prepares the configuration change and signals the device to retrieve it (17.6+). In the push workflow, Manager applies the ...

ekhabaro · 10-13-2026

vManage derives a device-specific configuration difference before applying a Configuration Group deployment. It does not send the complete intended configuration as a top-level replace. Depending on the device’s supported deployment path, vManage eit...

ekhabaro · 10-13-2026

Bear with me, I have used some AI to come up with the reply, but anyway, hope it helps and let me know:Nexus can include TCP/UDP ports in its ECMP hash, but ordinary ECMP does not track whether a TCP connection is established. When the next-hop set c...

ekhabaro · 10-13-2026

By the way, this questions was already asked before: https://community.cisco.com/t5/routing-and-sd-wan/cisco-sd-wan-mark-as-optional/m-p/4988460

ekhabaro · 10-13-2026

Is 20.18 an option for you? IPv4/IPv6 route in a service VPN parcel is optional there. I've just verified it in 20.18.4 for you and applied the configuration change successfully without specifying ipv4 route variables.

Member Since	‎10-06-2017 08:34 AM
Date Last Visited	‎10-13-2026 04:58 AM
Posts	219
Total Helpful Votes Received	357

User Statistics

User Activity

SD-WAN Configuration Example: How to prefer particular uplink for DIA

SD-WAN Configuration Example: Multiple transports and traffic engineering with centralized control policy and app route policy

SD-WAN TechTip: vEdge does not advertise its own AS when BGP routes are advertised into OMP

SD-WAN TechTip: OMP path selection corner case when egress path selection enforced on vEdge ("vSmart Doesn't Take into Account TLOC State on Remote vEdge")

SD-WAN Configuration Example: Site-to-site (LAN to LAN) IPSec between vEdge and Cisco IOS

Re: SD-WAN Configuration push

Re: SD-WAN Configuration push

Re: Cisco nexus BGP with multi path hashing issue

Re: Optional IPv4 Static route in Service VPN

Re: Optional IPv4 Static route in Service VPN