cancelar
Mostrando los resultados de 
Buscar en lugar de 
Quiere decir: 
cancel
1278
Visitas
10
ÚTIL
2
Respuestas

Rommon AIR-AP1131AG-N-K9 no carga IOS desde TFTP server

iccjflores
Level 1
Level 1

Hola, tengo un AP 1131, el cual se fue a rommon, al parecer creo cargo un IOS erroneo pero cuando le quiero cargar el IOS de autonomo por TFTP server no lo hace me manda varias mensajes, ya realice algunos procedimientos y aun asi no lo hace, ojala me puedan ayudar... Slds

El Led del AP esta en color morado o lila fijamente....

Este es el LOG

Xmodem file system is available.
flashfs[0]: Checking block 87...bad block number (-1)
flashfs[0]: erasing block 87...
intel_28f128j3a_erase_sector: erase block errorflashfs[0]: erasing block, flash handle 0x1eeedd4, device 0, offset 0xae0000: Operation Failed

The system has been interrupted, or encountered an error
during initializion of the flash filesystem. The following
commands will initialize the flash filesystem, and finish
loading the operating system software:

flash_init
ether_init
tftp_init
boot


ap: flash_init
Initializing Flash...
flashfs[0]: Checking block 87...bad block number (-1)
flashfs[0]: erasing block 87...
intel_28f128j3a_erase_sector: erase block errorflashfs[0]: erasing block, flash handle 0x1eeedd4, device 0, offset 0xae0000: Operation Failed
...done Initializing Flash.

ap: ether_init
Initializing ethernet port 0...
Reset ethernet port 0...
Reset done!
ethernet link up, 100 mbps, full-duplex
Ethernet port 0 initialized: link is up

ap: set IP_ADDR 10.0.0.1
flash:/env_vars.tmp: invalid argument
The filesystem containing the variables may not be initialized yet.

ap: set NETMASK 255.255.255.0
flash:/env_vars.tmp: invalid argument
The filesystem containing the variables may not be initialized yet.

ap: set DEFAULT_ROUTER 10.0.0.2
flash:/env_vars.tmp: invalid argument
The filesystem containing the variables may not be initialized yet.

ap: tftp_init
tftp_init success: You can now use tftp file system!

ap: tar -xtract tftp://10.-0
usage: tar <-table | -xtract> <tar file> <destination>

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5.default flash:

extracting info (274 bytes)flash:/info: invalid argument

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5 flash:
tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5: no such file or directory

ap: tar -xtract tftp://10.0.0.2/1130/Autonomous/c1130-k9w7-tar.123-7.JA5.default flash:
tftp://10.0.0.2/1130/Autonomous/c1130-k9w7-tar.123-7.JA5.default: no such file or directory

ap: tar -xtract tftp://10.0.0.2/1130/Autonomous/c1130-k9w7-tar.123-7.JA5 flash:
tftp://10.0.0.2/1130/Autonomous/c1130-k9w7-tar.123-7.JA5: no such file or directory

ap: tar -xtract tftp://10.0.0.2c1130-k9w7-tar.123-7.JA5.tar
*** line too large ***

usage: tar <-table | -xtract> <tar file> <destination>


ap: tar-xtract tftp://10.0.0.2/1130/Auotonomous/c1130-k9w7-tar.123-7.JA5.tar flash: Unknown cmd: tar-xtract

ap: tar -xtract tftp://10.0.0.2/1130/Autonomous/c1130-k9w7-tar.123-7.JA5.tar flash:
tftp://10.0.0.2/1130/Autonomous/c1130-k9w7-tar.123-7.JA5.tar: no such file or directory

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5.default flash:

extracting info (274 bytes)flash:/info: invalid argument

ap: tftp_init

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5.default flash:

extracting info (274 bytes)flash:/info: invalid argument

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5.tar flash:

extracting info (274 bytes)flash:/info: invalid argument

ap:

ap:

ap:

ap:

ap:

ap:

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5 flash:
tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5: no such file or directory

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5.tar flash:
Unknown cmd: tar

ap: tftp_init

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5.default flash:

extracting info (274 bytes)flash:/info: invalid argument

ap:

ap:

ap:

ap:

ap:

ap:

ap:

ap: tar -xtract tftp://10.0.2/c1130-k9w7-tar.123-7.JA5.tar flash:
tftp://10.0.2/c1130-k9w7-tar.123-7.JA5.tar: invalid argument

ap: tftp_init

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5.tar flash:

extracting info (274 bytes)flash:/info: invalid argument

ap:

ap:

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5 flash:
tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5: connection timed out

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5 flash:
Unknown cmd: tar

ap: tftp_init

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5 flash:

extracting info (274 bytes)flash:/info: invalid argument

ap: tar -xtract tftp://10.0.0.2/c1130-k9w7-tar.123-7.JA5 flash:

extracting info (274 bytes)flash:/info: invalid argument

ap: version
C1130 Boot Loader (C1130-BOOT-M) Version 12.3(8)JEA, RELEASE SOFTWARE (fc2)
Technical Support: http://www.cisco.com/techsupport
Compiled Mon 28-Aug-06 12:08 by kellythw

ap:

2 RESPUESTAS 2

juan soporteco
Level 1
Level 1

Ya pudiste resolver el problema, me sucede algo muy similar con un 3502i, al agregar los comandos esta es la siguiente salida:

 

 

ap: dir flash:
unable to stat flash:/: invalid argument

ap: fsck flash:
Are you sure you want to fsck "flash:" (could take some time) (y/n)?y
flashfs[0]: Checking block 41...bad block number (15)
flashfs[0]: erasing block 41...flashfs[0]: writing to flash handle 0x2314ff0, device 0, offset 0x520000, length: 0x20: Operation Failed
Filesystem "flash:" not checked -- I/O error

ap: format flash:
Are you sure you want to format "flash:" (all data will be lost) (y/n)?y
flashfs[0]: Checking block 41...bad block number (15)
flashfs[0]: erasing block 41...flashfs[0]: writing to flash handle 0x2314ff0, device 0, offset 0x520000, length: 0x20: Operation Failed
Filesystem "flash:" not formatted -- I/O error

ap: set IP_ADDR x.x.x.x
Unknown cmd: set

ap: set NETMASK x.x.x.x
flash:/env_vars.tmp: invalid argument
The filesystem containing the variables may not be initialized yet.

ap: set DEFAULT_ROUTER x.x.x.x
flash:/env_vars.tmp: invalid argument
The filesystem containing the variables may not be initialized yet.

ap: flash_init
Initializing Flash...
flashfs[0]: Checking block 41...bad block number (15)
flashfs[0]: erasing block 41...flashfs[0]: writing to flash handle 0x2314ff0, device 0, offset 0x520000, length: 0x20: Operation Failed
...done Initializing Flash.

ap: fsck flash:
Unknown cmd: fsck

ap: set IP_ADDR  x.x.x.x
flash:/env_vars.tmp: invalid argument
The filesystem containing the variables may not be initialized yet.

ap: ether_init
Ethernet speed is 1000 Mb - FULL duplex

ap:

 

quedo atento a tu respuesta dado que he buscado en diferentes lugares pero no hay una solucion a este problema

Hola @juan soporteco

Creo que deberías de abrir un caso con el TAC ya que parece ser un problema la memoria flash.

Espero que la información haya sido útil y si no tienes más preguntas recuerda cerrar el topic, seleccionando la respuesta como "Respuesta correcta"
**Please rate the answer if this information was useful***
**Por favor si la información fue util marca esta respuesta como correcta**
Vamos a comenzar

¡Conecte con otros expertos de Cisco y del mundo! Encuentre soluciones a sus problemas técnicos o comerciales, y aprenda compartiendo experiencias.

Queremos que su experiencia sea grata, le compartimos algunos links que le ayudarán a familiarizarse con la Comunidad de Cisco: