取消
显示结果 
搜索替代 
您的意思是: 
cancel
1984
查看次数
0
有帮助
3
回复

3850交换机端口汇聚

wx_UpQwv50V
Level 1
Level 1
cisco3850#configure
Configuring from terminal, memory, or network [terminal]?
Enter configuration commands, one per line. End with CNTL/Z.
cisco3850(config)#monitor session 1 source vlan 188
cisco3850(config)#monitor session 1 destination interface gigabitEthernet 1/0/24
cisco3850(config)#exi
cisco3850(config)#exit
cisco3850#wr
Building configuration...
[OK]
cisco3850#show mon
% Incomplete command.
端口汇聚完成后,能正常使用,单通过show命令查看不断有汇聚配置,求大神指导
3 条回复3

wx_UpQwv50V
Level 1
Level 1
cisco3850#show interfaces gigabitEthernet 1/0/24
GigabitEthernet1/0/24 is up, line protocol is down (monitoring)
Hardware is Gigabit Ethernet, address is xxxxxxxxxxxxx (xxxxxxxxxxx)
MTU 1500 bytes, BW 1000000 Kbit/sec, DLY 10 usec,
reliability 255/255, txload 10/255, rxload 1/255
Encapsulation ARPA, loopback not set
Keepalive set (10 sec)
Full-duplex, 1000Mb/s, media type is 10/100/1000BaseTX
input flow-control is off, output flow-control is unsupported
ARP type: ARPA, ARP Timeout 04:00:00
Last input never, output 00:49:43, output hang never
Last clearing of "show interface" counters never
Input queue: 0/2000/0/0 (size/max/drops/flushes); Total output drops: 3328663
Queueing strategy: fifo
Output queue: 0/40 (size/max)
5 minute input rate 0 bits/sec, 0 packets/sec
5 minute output rate 42875000 bits/sec, 20357 packets/sec
0 packets input, 0 bytes, 0 no buffer
Received 0 broadcasts (0 multicasts)
0 runts, 0 giants, 0 throttles
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
0 watchdog, 0 multicast, 0 pause input
0 input packets with dribble condition detected
62026680 packets output, 18350625839 bytes, 0 underruns
0 output errors, 0 collisions, 2 interface resets
0 unknown protocol drops
0 babbles, 0 late collision, 0 deferred
0 lost carrier, 0 no carrier, 0 pause output
0 output buffer failures, 0 output buffers swapped out
端口有流量

l_enough
Spotlight
Spotlight
端口镜像还是端口汇聚?
1.show monitor session 1,查看配置
2.如镜像到vcenter这些虚拟化接口,在虚拟化还需要单独配置

wx_UpQwv50V
Level 1
Level 1
l_enough1 发表于 2019-7-8 10:19
端口镜像还是端口汇聚?
1.show monitor session 1,查看配置
2.如镜像到vcenter这些虚拟化接口,在虚拟 ...

谢谢,两个交换机,一个3560,一个3850,3560 show mon 就可以,3850 就得 show mon session 1 才能看到,非常感谢:)
快捷链接