WS-C2960X-24PS-L 해당 스위치에서 특이 로그가 보이는데 해석이 어렵습니다 이런 로그는 어떻게 조치 할 수 있나요?

[asa1413]

Jan 3 09:48:08.028 KST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to down
Jan 3 09:48:09.034 KST: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to down
Jan 3 09:48:12.149 KST: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to up
Jan 3 09:48:13.348 KST: %SPANTREE-2-RECV_PVID_ERR: Received BPDU with inconsistent peer vlan id 10 on GigabitEthernet1/0/2 VLAN1.
Jan 3 09:48:13.348 KST: %SPANTREE-2-BLOCK_PVID_LOCAL: Blocking GigabitEthernet1/0/2 on VLAN0001. Inconsistent local vlan.
Jan 3 09:48:13.348 KST: %SPANTREE-2-BLOCK_PVID_PEER: Blocking GigabitEthernet1/0/2 on VLAN0250. Inconsistent peer vlan.
Jan 3 09:48:14.158 KST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to up
Jan 3 09:48:28.356 KST: %SPANTREE-2-UNBLOCK_CONSIST_PORT: Unblocking GigabitEthernet1/0/2 on VLAN0001. Port consistency restored.
Jan 3 09:48:28.356 KST: %SPANTREE-2-UNBLOCK_CONSIST_PORT: Unblocking GigabitEthernet1/0/2 on VLAN0250. Port consistency restored.
Jan 3 09:50:14.373 KST: %ILPOWER-7-DETECT: Interface Gi1/0/2: Power Device detected: IEEE PD
Jan 3 09:50:44.373 KST: %ILPOWER-3-CONTROLLER_PORT_ERR: Controller port error, Interface Gi1/0/2: Power given, but Power Controller does not report Power Good
Jan 3 09:50:54.426 KST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to down
Jan 3 09:50:55.432 KST: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to down
Jan 3 09:50:59.026 KST: %LINK-3-UPDOWN: Interface GigabitEthernet1/0/2, changed state to up
Jan 3 09:51:00.224 KST: %SPANTREE-2-RECV_PVID_ERR: Received BPDU with inconsistent peer vlan id 250 on GigabitEthernet1/0/2 VLAN1.
Jan 3 09:51:00.224 KST: %SPANTREE-2-BLOCK_PVID_PEER: Blocking GigabitEthernet1/0/2 on VLAN0250. Inconsistent peer vlan.
Jan 3 09:51:00.224 KST: %SPANTREE-2-BLOCK_PVID_LOCAL: Blocking GigabitEthernet1/0/2 on VLAN0001. Inconsistent local vlan.
Jan 3 09:51:01.032 KST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/2, changed state to up
Jan 3 09:51:15.226 KST: %SPANTREE-2-UNBLOCK_CONSIST_PORT: Unblocking GigabitEthernet1/0/2 on VLAN0250. Port consistency restored.
Jan 3 09:51:15.226 KST: %SPANTREE-2-UNBLOCK_CONSIST_PORT: Unblocking GigabitEthernet1/0/2 on VLAN0001. Port consistency restored.
Jan 3 09:55:00.566 KST: %LINK-5-CHANGED: Interface GigabitEthernet1/0/15, changed state to administratively down
Jan 3 09:55:01.569 KST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/15, changed state to down
Jan 3 09:55:08.081 KST: %SYS-5-CONFIG_I: Configured from console by dwhn on vty0 (10.4.40.38)
Jan 3 09:55:09.046 KST: %LINK-5-CHANGED: Interface GigabitEthernet1/0/17, changed state to administratively down
Jan 3 09:55:10.045 KST: %LINEPROTO-5-UPDOWN: Line protocol on Interface GigabitEthernet1/0/17, changed state to down

[ammahend · Accepted solution]

The specified interface has received an BPDU that is tagged with a VLAN ID that does not match the VLAN ID on interface on which the BPDU was received. This condition occurs when the native VLAN is not consistently configured, I have also seen this issue with Cisco and Juniper even if vlan is configured correctly, share the config on the port and remote side.

[asa1413]

spanning-tree mode rapid-pvst로 설정값을 변경했더니 해결되었습니다. 설명해주신 내용과 같은 내용일까요?