Cisco 커뮤니티 팀은 콘텐츠 신디케이션의 두 번째 단계를 발표하게 되어 매우 기쁘게 생각합니다. 1단계에서는 솔루션으로 동의/채택된 콘텐츠가 영어 커뮤니티에서 다른 언어의 커뮤니티로 번역, 배포되어 글로벌 커뮤니티 멤버들에게 유용한 추가 정보를 제공할 수 있었습니다. 이번 2단계는 비영어권 커뮤니티에서 답변이 제공되지 않은 토론 게시물이 영어로 번역되어 영어권 커뮤니티에 배포됩니다. 이러한 방법을 통해 훨씬 더 많은 사용자와 멤버가 이 게...
포럼 게시물
Hi everyone,I have a question about nexus 9805 power redundancy.It uses 3000w AC power and is connected to power supply slots 1, 2, 3, and 4.After testing the equipment, I found that the module worked properly when three power sources were connected....
After connecting to the console, the following logs occur in real time on the screen you see.Is there any way to deal with it?1. vss_cdp_tlv_receive_notify: Invalid TLV Real-time occurred2. %C4K_SWITCHINGENGINEMAN-4-VFEL2INTERRUPT: VFE L2 Memory in...
안녕. nexus93180YC-EX 대신 nexus3550-T 장비를 사용해도 괜찮나요? 그리고 두 장비의 차이점도 알려주세요.
The following command to filter and send route information in the out direction cannot be executed.It seems that filtering is done only in the in direction. Is the filtering function in the out direction gone?router ospf 1network 10.0.0.0 0.255.255.2...
Does anyone know the bgp nsr configuration on the C6500, C9400 Catalyst Switch?There is a command called nsr in ospf, but I can't find bgpPlease let me know if you know!!
Hi I am Jeong I configured HSRP with two ME3600X.Same configuration, but with ACTIVE-ACTIVE configuration on some equipmentHSRP operates separately and STANDBY is displayed as UNKNOWN.I'm curious what the problem is.
HelloI was using one HWIC-4ESW module on the Cisco 2911/K9But I didn't have enough ports, so I added HWIC-4ESWAnd HWIC-4ESW did an abnormal moveInterface and protocol all came up, but the ping didn't goWhat I checked was1. The ping went well when I c...
hello! If i enable the VPC function, the loopback will be down. (nxosv9k-9.3.9 In the eve-ng environment)It doesn't seem to be down under all conditions, but I'd like to know under what conditions loopback will be down when VPC is enabled. If i activ...
Packet Tracer asa 5506 has finished setting up object and object-group, and has set access-list and access-group, but packets heading to dmz are dropped
I added routing as follows, but the MAC address is different as shown in the picture below. How do I fix it?
I want to make a remote access vpn so that I can access through the radius server user rather than the local user using aaa on the packet tracer router.
I need OSPF routing in the following environment and I want to use Frame-Relay without using subinterfaces.
EVE-NG 가상 환경에서 i86bi_linux_l2-adventerprisek9-ms.SSA.high_iron_20190423.bin 이미지를 사용하여 L2/L3 컨피그를 설정 중에 있습니다. 해당 이미지의 스위치에서 NAT를 사용하고자 하는데, 정상적으로 작동하지 않는 문제가 발생하고 있습니다. 정확하게는 nat inside interface로 연결되어있는 네트워크에서 nat outside의 네트워크로 통신을 하고자 하면 NAT가 동작하지 ...
After booting the switch, the system configuration dialog should appear and console access should be established. i am not What do you think is the problem?
WAN을 구성하려면, 라우터 간 연결을 위해 serial port(cable)을 사용합니다.왜 시리얼 포트만을 사용하는거죠? 이더넷 연결은 안 되나요?
