05-15-2019 12:04 AM - edited 05-15-2019 12:04 AM
I am getting fail Out-of-Band EPG-default. Please help me on how to solve it is? as shown below describe the problem.
Configuration issue: Configuration failed
Configuration state: EPG default due to IDs Not Allocated
Kindly have a look at my issue.
Solved! Go to Solution.
05-15-2019 02:06 PM
Hi @AA.Ahsan ,
Regarding your fault (I've put your screendump inline to make it easier to see)
I have one question for you. Have you allocated OOB Mangement addresses to each of your nodes from within ACI? I'm not sure if this will fix your problem, but it's a start.
I hope this helps
Don't forget to mark answers as correct if it solves your problem. This helps others find the correct answer if they search for the same problem
05-15-2019 02:06 PM
Hi @AA.Ahsan ,
Regarding your fault (I've put your screendump inline to make it easier to see)
I have one question for you. Have you allocated OOB Mangement addresses to each of your nodes from within ACI? I'm not sure if this will fix your problem, but it's a start.
I hope this helps
Don't forget to mark answers as correct if it solves your problem. This helps others find the correct answer if they search for the same problem
05-17-2019 10:24 PM
05-17-2019 10:27 PM
hi,
I have already assigned static node management IP address but cannot get a ping from OOB mgmt.
also, I have manually assign OOB mgmt IP address in CLI mode, it is putting but can't get the pin from OOB mgmt.
Note: after assigned IP address to OOB mgmt that time default EPG is showing an error message.
05-18-2019 02:39 PM
Hi @AA.Ahsan ,
I'm running out of ideas without finding a solution, but I do notice in your screendump of Static Node Mangement Addresses - you don't have any addresses for nodes 1, 2 or 3 (The APICs - assuming 3 APICs)
Also, the output of your show oob-mgmt command shows only ONE node (even though the Static Node Mangement Addresses screendum shows 3 addresses). I have NO idea why that is.
My lab has only one APIC, and I haven't tried to set up any contracts to an external L3, so I don't see anything regarding contracts (and that maybe where you problem lies) but this is what I'd expet to see for Static Node Mangement Addresses and the output of the show oob-mgmt command.
apic1# show oob-mgmt Table1 : OOB-Mgmt Node Details Type Node ID Ip Address Gateway OOB-EPG Oper State --------------- ---------- -------------------- -------------------- -------------------- ---------- Leaf102 102 172.16.12.117/24 172.16.12.1 default up apic1 1 172.16.12.111/24 172.16.12.1 default up Leaf101 101 172.16.12.116/24 172.16.12.1 default up Spine201 201 172.16.12.114/24 172.16.12.1 default up Table2 : OOB-Mgmt EPG Details Name Qos Tag Nodes Oper State --------------- --------------- --------------- ---------- ---------- default unspecified 49153 102 up default unspecified 49153 1 up default unspecified 49153 101 up default unspecified 49153 201 up Table3 : OOB-Mgmt EPG Contract Details Provider OOB-MGMT-EPG Contracts Consumer OOB-Mgmt Ext-L3 Epg Oper State --------------- --------------- ------------------------- ---------- Table4 : OOB-Mgmt External L3 EPG Details Name Qos Contract Nodes IP Network Oper State --------------- --------------- --------------- ---------- ---------- ---------- apic1#
BTW - I appreciate you marking the answer I gave before as correct, but I suggest you un-mark it as correct until we find a solution, otherwise other people wiser thatn me may igrore this thread
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide