10-31-2012 02:20 AM
Re: Access Server through VIP (ACE 4710) but very slow
Hi Shiva
Kindly Help .....Accessing the server very slow.., Plz check my real configuration... this configuration is for application server and after this i have to configure more serverfarm for different server like webmail etc. in this ACE 4710. I have only one ACE 4710 .
ACE Version A4(2.0) = is there supports Probe with this version.??? without probe server will work but very slow. And plz guide Nat-pool is required
VIP :-- 172.16.15.8
LB/Admin# sh run
Generating configuration....
no ft auto-sync startup-config
logging enable
logging host 172.29.91.112 udp/514
resource-class RC1
limit-resource all minimum 10.00 maximum unlimited
boot system image:c4710ace-mz.A4_2_0.bin
hostname LB
interface gigabitEthernet 1/1
description Management
speed 1000M
switchport access vlan 1000
no shutdown
interface gigabitEthernet 1/2
description clientside
switchport access vlan 30
no shutdown
interface gigabitEthernet 1/3
description serverside
switchport access vlan 31
no shutdown
interface gigabitEthernet 1/4
no shutdown
context Admin
description Management
member RC1
access-list everyone line 8 extended permit ip any any
access-list everyone line 16 extended permit icmp any any
probe http probe1
description health check
interval 5
passdetect interval 10
request method head
expect status 200 200
open 1
rserver redirect https_redirect
description redirect traffic to https
webhost-redirection / 302
inservice
rserver redirect maintenance_page
description maintenance page displayed
webhost-redirection /sry.html 301
inservice
rserver host web1
ip address 192.168.10.3
inservice
rserver host web2
ip address 192.168.10.4
inservice
rserver host web3
ip address 192.168.10.5
inservice
serverfarm host http
rserver web1
inservice
rserver web2
inservice
rserver web3
inservice
serverfarm redirect https_redirect_farm
description Redirect traffic to https
serverfarm redirect maintenance_farm
description send user to maintenance page
parameter-map type connection paramap_http
description parameter connection tcp
exceed-mss allow
sticky ip-netmask 255.255.255.0 address source Sticky_http
timeout activeconns
serverfarm http
class-map match-all REMOTE-ACCESS
class-map type management match-any remote_access
2 match protocol xml-https any
3 match protocol icmp any
4 match protocol telnet any
5 match protocol ssh any
6 match protocol http any
7 match protocol https any
8 match protocol snmp any
class-map match-all slb-vip
2 match virtual-address 172.16.15.8 tcp eq www
policy-map type management first-match remote_access
class class-default
permit
policy-map type management first-match remote_mgmt_allow_policy
class remote_access
permit
policy-map type loadbalance first-match slb
class class-default
serverfarm http
policy-map type inspect http all-match slb-vip-http
class class-default
permit
policy-map multi-match client-vips
class slb-vip
loadbalance vip inservice
loadbalance policy slb
loadbalance vip icmp-reply active
inspect http policy slb-vip-http
connection advanced-options paramap_http
interface vlan 30
description "Client Side"
ip address 172.16.15.24 255.255.255.0
access-group input everyone
service-policy input client-vips
no shutdown
interface vlan 31
description "Server Side"
ip address 192.168.10.1 255.255.255.0
service-policy input remote_access
no shutdown
interface vlan 1000
description managment
ip address 172.29.91.110 255.255.255.0
service-policy input remote_mgmt_allow_policy
no shutdown
ip route 0.0.0.0 0.0.0.0 172.16.15.1
snmp-server contact "PHQ"
snmp-server community phq group Network-Monitor
snmp-server trap-source vlan 1000
username admin password 5 $1$b2txbc5U$TA74D920oSdd2eOZ4hSFe/ role Admin domain
default-domain
username www password 5 $1$.GuWwQEK$r8Ub4OcE3l190d5GA4kvR. role Admin domain de
fault-domain
username prem password 5 $1$8C7eRKrI$it3UV4URZ26X4S/Bh6OEr0 role Admin domain d
efault-domain
ssh key rsa 1024 force
banner motd # "ro" #
Regards,
Prem
11-01-2012 03:31 AM
Hi Prem,
Is this working fine when you access the server directly? If so take a packet capture for both scenario and verify if any difference or raise a TAC case so we can take a look.
HTH
-
Siva
11-07-2012 12:55 AM
Hi Shiva,
plz guide i'm new with ACE LB, also find my n/w design for connected ace to server. but server accessing very very slow, but when i connect through my old server software LB (with two interface)then accessing very fast. I just replace my old serverLB(with two interface) to ACE4710 and connect the same scenario then why not server accessing smoothly with VIP .Reply soon only I connect ACE's two interface with switch.....
Regards,
Prem
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide