05-28-2012 09:59 PM
How can you check if balance ACA is enabled in CSS11503? How can you see also if the content switch(CSS11503) is load balancing using balance ACA? "show load" command does not show it.
xxxxxx# show load
Global load information:
Reporting:Enabled
Calculation method:Relative
Step Size:Dynamic Configured:10 Actual:1280
Threshold:254 Ageout-Timer:60
Teardown-timer: Configured:20 Actual:20
Service load information:
Average Average Peak Average
Service Name Load Number ResponseTime Response Time
-----------------------------------------------------------------------
DNS1 4 8999 33972
DNS2 4 8884 28254
SSH-WPHGT11 2 0 87509
WPHGT11 2 0 0
def-gwy-server 255 0 0
fe1-gw1-radius1 2 0 0
fe1-gw1-radius2 2 0 0
fe1-gw1-wap-8799 8 15344 662337
fe1-gw1-wap-9200 2 0 23751
fe1-gw1-wap-9201 19 30815 1060772
fe1-gw1-wap-9202 2 3442 20998
fe1-gw1-wap-9203 2 0 601421
fe1-gw2-radius1 2 0 0
fe1-gw2-radius2 2 0 0
fe1-gw2-wap-8799 6 13041 704099
fe1-gw2-wap-9200 2 3182 14139
fe1-gw2-wap-9201 43 60856 1065916
fe1-gw2-wap-9202 2 0 20879
fe1-gw2-wap-9203 2 0 506349
fe1-gw3-radius1 2 0 0
fe1-gw3-radius2 2 0 0
fe1-gw3-wap-8799 4 10212 1092052
fe1-gw3-wap-9200 2 0 21320
fe1-gw3-wap-9201 20 29867 1023362
fe1-gw3-wap-9202 2 8490 51904
fe1-gw3-wap-9203 2 0 734375
fe2-gw1-radius1 2 0 0
fe2-gw1-radius2 2 0 0
fe2-gw1-wap-8799 3 7877 853708
fe2-gw1-wap-9200 2 0 10895
fe2-gw1-wap-9201 79 107955 1040622
fe2-gw1-wap-9202 2 0 34262
fe2-gw1-wap-9203 29 35629 605709
fe2-gw2-radius1 2 0 0
fe2-gw2-radius2 2 0 0
fe2-gw2-wap-8799 4 11740 887388
fe2-gw2-wap-9200 2 0 13231
fe2-gw2-wap-9201 78 104708 917860
fe2-gw2-wap-9202 2 0 24661
fe2-gw2-wap-9203 2 0 589902
hsp1-ppg1 2 140 31000
hsp2-ppg1 2 96 31036
hsp3-ppg1 255 0 0
pmaster 2 0 1999716
serverchat 255 0 0
serverchat2 255 0 0
smaster 2 0 1934905
05-29-2012 04:20 PM
Hi Henry,
The easy way is checking the Content Rule configuration, with balance ACA, it should look like this:
content xxxxx
vip address x.x.x.x
port xx
protocol tcp
url "/*"
add service xxxx
balance aca==========> you should see this line if ACA is in use
active
---------------------------------
Cesar R
05-29-2012 04:39 PM
yup.. that i know.. but is there any other way other than the show run?
05-29-2012 04:46 PM
You can use the show rule {owner name} . It gives you an output like this;
Name: fXXXX Owner: XXXXXX
State: Active Type: HTTP
Balance: ACA Failover: N/A
Persistence: Enabled Param-Bypass: Disabled
Session Redundancy: Disabled
IP Redundancy: Not Redundant
L3: X.X.X.X
L4: TCP/80
Url: /*
Redirect: ""
TCP RST client if service unreachable: Disabled
Rule Services & Weights:
1: XXX-Alive, S-1
---------------------------------
Cesar R
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide