cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1133
Views
0
Helpful
1
Replies

WAVE 594-K9 bloc

ccieexpertadmin
Level 1
Level 1

hi , 

please  i have WAVE 594-k9 diplays the following ouput after reload then i dont have acces to maange it 

Wait for BMC ...
Wait for BMC 10 seconds
Wait for BMC 10 seconds
Wait for BMC 10 seconds
Wait for BMC 10 seconds
Wait for BMC initial Successfully
BIOS POST ongoing
Booting system, please wait.........


Cisco BIOS A31C118A Build 001
CPU Type: Intel(R) Xeon(R) CPU X3430 @ 2.40GHz, 2394 MHz
Build Date:09/19/2012 15:52:26
Total Memory:12288 MB(DDR3 800)
System memory:619 KB ,Extened Memory:3573 MB


PCI Device Table:
Bus Dev Func VendID DevID Class IRQ
---------------------------------------------------------
00 00 00 8086 D130 Bridge Device
00 03 00 8086 D138 PCI Bridge,IRQ=11
00 05 00 8086 D13A PCI Bridge,IRQ=11
00 08 00 8086 D155 System Device
00 08 01 8086 D156 System Device
00 08 02 8086 D157 System Device
00 08 03 8086 D158 System Device
00 10 00 8086 D150 System Device
00 10 01 8086 D151 System Device
00 16 00 8086 3B64 I/O Port Device,IRQ=11
00 1A 00 8086 3B3C USB Controller,IRQ=11
00 1C 00 8086 3B42 PCI Bridge,IRQ=10
00 1C 04 8086 3B4A PCI Bridge,IRQ=10
00 1C 06 8086 3B4E PCI Bridge,IRQ=5
00 1C 07 8086 3B50 PCI Bridge,IRQ=3
00 1D 00 8086 3B34 USB Controller,IRQ=7
00 1E 00 8086 244E PCI Bridge,IRQ=255
00 1F 00 8086 3B14 Bridge Device
00 1F 02 8086 3B22 SATA DPA,IRQ=3
00 1F 03 8086 3B30 SMBus,IRQ=5
01 00 00 10B5 8624 PCI Bridge,IRQ=11
02 04 00 10B5 8624 PCI Bridge,IRQ=11
02 05 00 10B5 8624 PCI Bridge,IRQ=10
02 06 00 10B5 8624 PCI Bridge,IRQ=5
02 08 00 10B5 8624 PCI Bridge,IRQ=11
02 09 00 10B5 8624 PCI Bridge,IRQ=10
06 00 00 8086 10C9 Ethernet,IRQ=11
06 00 01 8086 10C9 Ethernet,IRQ=10
07 00 00 8086 10C9 Ethernet,IRQ=10
07 00 01 8086 10C9 Ethernet,IRQ=5
09 00 00 177D 0010 Cavium Encryption,IRQ=11
0A 00 00 8086 10D3 Ethernet,IRQ=11
FF 00 00 8086 2C50 Bridge Device
FF 00 01 8086 2C81 Bridge Device
FF 02 00 8086 2C90 Bridge Device
FF 02 01 8086 2C91 Bridge Device
FF 03 00 8086 2C98 Bridge Device
FF 03 01 8086 2C99 Bridge Device
FF 03 02 8086 2C9A Bridge Device
FF 03 04 8086 2C9C Bridge Device
FF 04 00 8086 2CA0 Bridge Device
FF 04 01 8086 2CA1 Bridge Device
FF 04 02 8086 2CA2 Bridge Device
FF 04 03 8086 2CA3 Bridge Device
FF 05 00 8086 2CA8 Bridge Device
FF 05 01 8086 2CA9 Bridge Device
FF 05 02 8086 2CAA Bridge Device
FF 05 03 8086 2CAB Bridge Device


Booting from UNIGEN PSH4000S2 PMAP
Consoles: serial port
BIOS drive C: is disk0
BIOS drive D: is disk1
BIOS 619kB/3657648kB available memory

Cisco/x86 bootstrap loader, Revision 1.1
(root@adbu-relbld-1, Sun Nov 4 11:55:25 PST 2012)
|
|| || | 1. Boot WAAS
|| || | r. Boot Rescue Image
|| || || || || || | x. Reboot
|| || || || || || | 9. Escape to loader prompt (also ESC)
|| || || || || || || || || |
|| || || || || || || || || |
|| || |

could anyone advice me what does mean 

thanks

1 Reply 1

hamza.tebib
Level 1
Level 1

Hossam,

Do you have a Console access to your device ? if not than you need too. It seems like you did otherwise you'll not going to be able to grab all that output.

It seems all normal to me try not to touch your keyboard for a good 10 or 15 minute during the booting time to allow the WAE to boot. for the first time it would prompt you for the initial setup and that's why I was asking if you have a direct console access. because it's the only way 

On that first setup you should be able to designate/setup management access and all that juicy stuff that no one can't wait to do.

anyway hope that help,

If you're question had to do with the BIOS/POS check for the hardware I would suggest to ignore it unless you're planning to work for the manufactory. if you have issue with the hardware call Cisco TAC to help you out with RMA (return) only if you're contract is in good standing shape$ of course.

 Best,

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: