Hi there.
i need litte help to interpret the crashlog on my router
Yesterday I wanted to put the port tengigabit 0/2/0 into operation on my ASR1006X. This was already configured. Only the fiber optic link was put into operation. When this was done the entire router rebooted (RP3 rebooted). I don't see why this was the case other than the message "Critical software exception, check bootflash:crashinfo_RP_00_00_20240416-143500-MEST"
cisco ASR1006-X (RP3) processor (revision RP3) with 15126048K/24590K bytes of memory.
Processor board ID FXS2102Q0MW
5 Gigabit Ethernet interfaces
3 Ten Gigabit Ethernet interfaces
2 Forty Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
67108864K bytes of physical memory.
7116799K bytes of eUSB flash at bootflash:.
97620247K bytes of SATA hard disk at harddisk:.
0K bytes of WebUI ODM Files at webui:.
------------------ show inventory ------------------
NAME: "Chassis", DESCR: "Cisco ASR1006-X Chassis"
PID: ASR1006-X , VID: V01 , SN: FXS2102Q0MW
NAME: "module 0", DESCR: "Cisco ASR1000 SPA Interface Processor 40"
PID: ASR1000-SIP40 , VID: V02 , SN: JAE1824076N
NAME: "SPA subslot 0/0", DESCR: "5-port Gigabit Ethernet Shared Port Adapter"
PID: SPA-5X1GE-V2 , VID: V02 , SN: JAE14110BDI
NAME: "subslot 0/0 transceiver 0", DESCR: "GE T"
PID: GLC-T , VID: V03 , SN: F2140233690
NAME: "subslot 0/0 transceiver 1", DESCR: "GE ZX"
PID: GLC-LH-SMD , VID: V01 , SN: EO12006122076
NAME: "subslot 0/0 transceiver 2", DESCR: "GE LX"
PID: GLC-LH-SMD , VID: V01 , SN: F2010576832
NAME: "subslot 0/0 transceiver 3", DESCR: "GE LX"
PID: GLC-LH-SMD , VID: V01 , SN: F2010576833
NAME: "subslot 0/0 transceiver 4", DESCR: "GE LX"
PID: F24-CI-GLC-LH-SM , VID: V03 , SN: EA130904031
NAME: "SPA subslot 0/1", DESCR: "1-port 10 Gigabit Ethernet Shared Port Adapter XFP based"
PID: SPA-1X10GE-L-V2 , VID: V03 , SN: SAL1612846M
NAME: "subslot 0/1 transceiver 0", DESCR: "OC192 + 10GBASE-L"
PID: XFP-10GLR-OC192SR , VID: V02 , SN: 3191510463
NAME: "SPA subslot 0/2", DESCR: "1-port 10 Gigabit Ethernet Shared Port Adapter XFP based"
PID: SPA-1X10GE-L-V2 , VID: V02 , SN: JAE1330EYEX
NAME: "subslot 0/2 transceiver 0", DESCR: "OC192 + 10GBASE-L"
PID: XFP-10GLR-OC192SR , VID: V04 , SN: ONT173404KJ
NAME: "SPA subslot 0/3", DESCR: "1-port 10 Gigabit Ethernet Shared Port Adapter XFP based"
PID: SPA-1X10GE-L-V2 , VID: V03 , SN: SAL16106EHX
NAME: "subslot 0/3 transceiver 0", DESCR: "OC192 + 10GBASE-L"
PID: XFP-10GLR-OC192SR , VID: V02 , SN: 3191510464
NAME: "module 1", DESCR: "Cisco ASR1000 Modular Interface Processor 100"
PID: ASR1000-MIP100 , VID: V01 , SN: JAE242024PF
NAME: "SPA subslot 1/0", DESCR: "2-port 40 Gigabit QSFP Ethernet Port Adapter"
PID: EPA-2X40GE , VID: V01 , SN: JAE231902WW
NAME: "subslot 1/0 transceiver 0", DESCR: "QSFP 40GE LR"
PID: QSFP-40GE-LR4 , VID: A , SN: F2220512968
NAME: "subslot 1/0 transceiver 1", DESCR: "QSFP 40GE LR"
PID: QSFP-40GE-LR4 , VID: A , SN: F2220512951
NAME: "module R0", DESCR: "Cisco ASR1000 Route Processor 3"
PID: ASR1000-RP3 , VID: V03 , SN: JAE23040PMF
NAME: "module F0", DESCR: "Cisco ASR1000 Embedded Services Processor, 100G"
PID: ASR1000-ESP100 , VID: V02 , SN: JAE202405SH
NAME: "Power Supply Module 0", DESCR: "Cisco 1100 Watt AC power supply for ASR1006-X, ASR1009-X Chassis"
PID: ASR1000X-AC-1100W , VID: V01 , SN: POG19485021
NAME: "Power Supply Module 1", DESCR: "Cisco 1100 Watt AC power supply for ASR1006-X, ASR1009-X Chassis"
PID: ASR1000X-AC-1100W , VID: V01 , SN: POG191380CH
NAME: "Power Supply Module 2", DESCR: "Cisco 1100 Watt AC power supply for ASR1006-X, ASR1009-X Chassis"
PID: ASR1000X-AC-1100W , VID: V01 , SN: PST2045Z09D
NAME: "Fan Tray 0", DESCR: "Cisco ASR1000X FAN Module"
PID: ASR1000X-FAN , VID: V01 , SN: FXS1932Q06B
NAME: "Fan Tray 1", DESCR: "Cisco ASR1000X FAN Module"
PID: ASR1000X-FAN , VID: V01 , SN: FXS1939Q1SG
Is there a bug in this IOS Software as this reason?
thank you
Christian
