cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
264
Views
0
Helpful
0
Replies

N9K-C93180YC-FX in boot loop "Boot disk not found, Resetting EUSB boot

terryt
Level 1
Level 1

Hi,

I would like to ask for help in one of our Cisco Switch. I am trying to power up the Cisco N9K-C93180YC-FX but it keeps booting in a loop wherein it shows the "Boot disk not found, Resetting EUSB bootflash".

I also noticed the led on the 4x fans on the rear doesn't light up when the switch is powered. Also, the STS LED on the right side keeps blinking amber.

When I tried to do ssh, the putty log shows below;

=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2024.11.19 16:32:33 =~=~=~=~=~=~=~=~=~=~=~=
Image valid


Image Signature verification was Successful.

Boot Time: 11/19/2024 8:32:57

Security Lock
[ 3.108735] ahci 0000:00:1f.2: controller reset failed (0x80000001)
Installing klm_card_index
done
Boot disk not found, Resetting EUSB bootflash
****BOOT DISK NOT FOUND****
[ 13.613120] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000ff00
[ 13.613120]
[ 13.722618] CPU: 0 PID: 1 Comm: init Tainted: G O 4.1.21-WR8.0.0.28-standard #1
[ 13.823773] Hardware name: Default string Default string/Default string, BIOS 5.11 06/14/2020
[ 13.925971] 0000000000000000 ffff88085b423e08 ffffffff9482b128 ffffffff94c57b88
[ 14.015042] ffff88085b423ec8 ffff88085b423e88 ffffffff94828ec3 ffff88085bfa8000
[ 14.104115] ffffffff00000010 ffff88085b423e98 ffff88085b423e38 ffffffff94e48a20
[ 14.193187] Call Trace:
[ 14.222467] [<ffffffff9482b128>] dump_stack+0x63/0x81
[ 14.284038] [<ffffffff94828ec3>] panic+0xc1/0x210
[ 14.341441] [<ffffffff940883fb>] do_exit+0xb1b/0xb20
[ 14.401967] [<ffffffff94088497>] do_group_exit+0x47/0xb0
[ 14.466660] [<ffffffff94088514>] SyS_exit_group+0x14/0x20
[ 14.532399] [<ffffffff9483390a>] sysenter_dispatch+0x7/0x25
[ 14.600223] Kernel Offset: 0x13000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffb7ffffff)
[ 14.729507] Rebooting in 5 seconds..
[ 19.771709] ACPI MEMORY or I/O RESET_REG.

CISCO MODULE
BIOS Ver: 5.42
Switch G5
RC Revision: 02.03.00

Memory Information:
MRC Revision:00.50.00
Total DRAM: 32768 MB
Memory TOLM: 80000000
PCIE BASE: 80000000 Size : 10000000
PCI32 BASE: 90000000 Limit: FBFFFFFF
PCI64 BASE: 80000000000 Limit: 83FFFFFFFFF
UC START: 80000000000 End : 84000000000
ME Operational Firmware Version: 06:3.0.3.59

DIMM Information:
Clock Speed: 1067MHz
Socket: 0x0 Channel: 0x0 Number: 0x0 Presence: Yes Size: 32GB
Socket: 0x0 Channel: 0x0 Number: 0x1 Presence: No
Socket: 0x0 Channel: 0x1 Number: 0x0 Presence: No
Socket: 0x0 Channel: 0x1 Number: 0x1 Presence: No

Detected CISCO IOFPGA
Booting from Primary BIOS
Code Signing Results: 0x0
Booting from Upgrade FPGA
IOFPGA Subsystem Vendor ID 0x1172
FPGA Revision : 0x1000022
FPGA ID : 0x1564687
FPGA Date : 0x20200410
Power Debug Register1 : 0x0
Power Debug Register2 : 0x90027
Reset Cause Register : 0x80000000
Boot Ctrl Register : 0xe0ff
FPGA Update Status : 0x20

Detected CISCO MIFPGA
MIFPGA Subsystem Vendor ID 0x1172
MIFPGA Version : 0x10
MIFPGA Date : 0x20170515
MIFPGA Update Status : 0x20
MIFPGA ID : 0x1555231

Board Type: SUMPIN

Bootable Disk is detected. Device Name: INTEL SSDSCKKB240G8K
Version 2.18.1260. Copyright (C) 2020 American Megatrends, Inc.
FPGA SPI Flash MfgId=0xC2, DevId=0x2018, DevSize=0x18

Board type 4
IOFPGA @ 0xd8000000
SLOT_ID @ 0xf
Set fan speed to 60%
Initializing fan controller...
Standalone chassis
check_bootmode: grub: Continue grub
Trying to read config file /boot/grub/menu.lst.local from (hd0,5)
Filesystem type is ext2fs, partition type 0x83


Security Lock
Booting bootflash:/nxos.9.3.3.bin
Trying diskboot
Filesystem type is ext2fs, partition type 0x83
Image valid


Image Signature verification was Successful.

Boot Time: 11/19/2024 8:34:11

Security Lock
[ 3.108657] ahci 0000:00:1f.2: controller reset failed (0x80000001)
Installing klm_card_index
done
Boot disk not found, Resetting EUSB bootflash
****BOOT DISK NOT FOUND****
[ 13.609722] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000ff00
[ 13.609722]
[ 13.719217] CPU: 0 PID: 1 Comm: init Tainted: G O 4.1.21-WR8.0.0.28-standard #1
[ 13.820372] Hardware name: Default string Default string/Default string, BIOS 5.11 06/14/2020
[ 13.922570] 0000000000000000 ffff88085b423e08 ffffffff8482b128 ffffffff84c57b88
[ 14.011641] ffff88085b423ec8 ffff88085b423e88 ffffffff84828ec3 ffff88085bfa8000
[ 14.100713] ffffffff00000010 ffff88085b423e98 ffff88085b423e38 ffffffff84e48a20
[ 14.189785] Call Trace:
[ 14.219066] [<ffffffff8482b128>] dump_stack+0x63/0x81
[ 14.280637] [<ffffffff84828ec3>] panic+0xc1/0x210
[ 14.338040] [<ffffffff840883fb>] do_exit+0xb1b/0xb20
[ 14.398565] [<ffffffff84088497>] do_group_exit+0x47/0xb0
[ 14.463259] [<ffffffff84088514>] SyS_exit_group+0x14/0x20
[ 14.528998] [<ffffffff8483390a>] sysenter_dispatch+0x7/0x25
[ 14.596822] Kernel Offset: 0x3000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffb7ffffff)
[ 14.725064] Rebooting in 5 seconds..
[ 19.767128] ACPI MEMORY or I/O RESET_REG.

CISCO MODULE
BIOS Ver: 5.42
Switch G5
RC Revision: 02.03.00

Memory Information:
MRC Revision:00.50.00
Total DRAM: 32768 MB
Memory TOLM: 80000000
PCIE BASE: 80000000 Size : 10000000
PCI32 BASE: 90000000 Limit: FBFFFFFF
PCI64 BASE: 80000000000 Limit: 83FFFFFFFFF
UC START: 80000000000 End : 84000000000
ME Operational Firmware Version: 06:3.0.3.59

DIMM Information:
Clock Speed: 1067MHz
Socket: 0x0 Channel: 0x0 Number: 0x0 Presence: Yes Size: 32GB
Socket: 0x0 Channel: 0x0 Number: 0x1 Presence: No
Socket: 0x0 Channel: 0x1 Number: 0x0 Presence: No
Socket: 0x0 Channel: 0x1 Number: 0x1 Presence: No

Detected CISCO IOFPGA
Booting from Primary BIOS
Code Signing Results: 0x0
Booting from Upgrade FPGA
IOFPGA Subsystem Vendor ID 0x1172
FPGA Revision : 0x1000022
FPGA ID : 0x1564687
FPGA Date : 0x20200410
Power Debug Register1 : 0x0
Power Debug Register2 : 0x90027
Reset Cause Register : 0x80000000
Boot Ctrl Register : 0xe0ff
FPGA Update Status : 0x20

Detected CISCO MIFPGA
MIFPGA Subsystem Vendor ID 0x1172
MIFPGA Version : 0x10
MIFPGA Date : 0x20170515
MIFPGA Update Status : 0x20
MIFPGA ID : 0x1555231

Board Type: SUMPIN

Bootable Disk is detected. Device Name: INTEL SSDSCKKB240G8K
Version 2.18.1260. Copyright (C) 2020 American Megatrends, Inc.
CISCO MODULE
BIOS Ver: 5.42
Switch G5
RC Revision: 02.03.00

Memory Information:
MRC Revision:00.50.00
Total DRAM: 32768 MB
Memory TOLM: 80000000
PCIE BASE: 80000000 Size : 10000000
PCI32 BASE: 90000000 Limit: FBFFFFFF
PCI64 BASE: 80000000000 Limit: 83FFFFFFFFF
UC START: 80000000000 End : 84000000000
ME Operational Firmware Version: 06:3.0.3.59

DIMM Information:
Clock Speed: 1067MHz
Socket: 0x0 Channel: 0x0 Number: 0x0 Presence: Yes Size: 32GB
Socket: 0x0 Channel: 0x0 Number: 0x1 Presence: No
Socket: 0x0 Channel: 0x1 Number: 0x0 Presence: No
Socket: 0x0 Channel: 0x1 Number: 0x1 Presence: No

Detected CISCO IOFPGA
Booting from Primary BIOS
Code Signing Results: 0x0
Booting from Upgrade FPGA
IOFPGA Subsystem Vendor ID 0x1172
FPGA Revision : 0x1000022
FPGA ID : 0x1564687
FPGA Date : 0x20200410
Power Debug Register1 : 0x0
Power Debug Register2 : 0x90027
Reset Cause Register : 0x80000000
Boot Ctrl Register : 0xe0ff
FPGA Update Status : 0x20

Detected CISCO MIFPGA
MIFPGA Subsystem Vendor ID 0x1172
MIFPGA Version : 0x10
MIFPGA Date : 0x20170515
MIFPGA Update Status : 0x20
MIFPGA ID : 0x1555231

Board Type: SUMPIN

Bootable Disk is detected. Device Name: INTEL SSDSCKKB240G8K
Version 2.18.1260. Copyright (C) 2020 American Megatrends, Inc.
FPGA SPI Flash MfgId=0xC2, DevId=0x2018, DevSize=0x18

Board type 4
IOFPGA @ 0xd8000000
SLOT_ID @ 0xf
Set fan speed to 60%
Initializing fan controller...
Standalone chassis
check_bootmode: grub: Continue grub
Trying to read config file /boot/grub/menu.lst.local from (hd0,5)
Filesystem type is ext2fs, partition type 0x83


Security Lock
Booting bootflash:/nxos.9.3.3.bin
Trying diskboot
Filesystem type is ext2fs, partition type 0x83
Image valid


Image Signature verification was Successful.

Boot Time: 11/19/2024 8:36:30

Security Lock
[ 3.108885] ahci 0000:00:1f.2: controller reset failed (0x80000001)
Installing klm_card_index
done
Boot disk not found, Resetting EUSB bootflash
****BOOT DISK NOT FOUND****
[ 13.609958] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000ff00
[ 13.609958]
[ 13.719456] CPU: 0 PID: 1 Comm: init Tainted: G O 4.1.21-WR8.0.0.28-standard #1
[ 13.820610] Hardware name: Default string Default string/Default string, BIOS 5.11 06/14/2020
[ 13.922809] 0000000000000000 ffff88085b423e08 ffffffff9b82b128 ffffffff9bc57b88
[ 14.011879] ffff88085b423ec8 ffff88085b423e88 ffffffff9b828ec3 ffff88085bfa8000
[ 14.100951] ffffffff00000010 ffff88085b423e98 ffff88085b423e38 ffffffff9be48a20
[ 14.190024] Call Trace:
[ 14.219304] [<ffffffff9b82b128>] dump_stack+0x63/0x81
[ 14.280875] [<ffffffff9b828ec3>] panic+0xc1/0x210
[ 14.338277] [<ffffffff9b0883fb>] do_exit+0xb1b/0xb20
[ 14.398803] [<ffffffff9b088497>] do_group_exit+0x47/0xb0
[ 14.463497] [<ffffffff9b088514>] SyS_exit_group+0x14/0x20
[ 14.529235] [<ffffffff9b83390a>] sysenter_dispatch+0x7/0x25
[ 14.597061] Kernel Offset: 0x1a000000 from 0xffffffff81000000 (relocation range: 0xffffffff80000000-0xffffffffb7ffffff)
[ 14.726343] Rebooting in 5 seconds..
[ 19.767992] ACPI MEMORY or I/O RESET_REG.

CISCO MODULE
BIOS Ver: 5.42
Switch G5
RC Revision: 02.03.00

Memory Information:
MRC Revision:00.50.00
Total DRAM: 32768 MB
Memory TOLM: 80000000
PCIE BASE: 80000000 Size : 10000000
PCI32 BASE: 90000000 Limit: FBFFFFFF
PCI64 BASE: 80000000000 Limit: 83FFFFFFFFF
UC START: 80000000000 End : 84000000000
ME Operational Firmware Version: 06:3.0.3.59

DIMM Information:
Clock Speed: 1067MHz
Socket: 0x0 Channel: 0x0 Number: 0x0 Presence: Yes Size: 32GB
Socket: 0x0 Channel: 0x0 Number: 0x1 Presence: No
Socket: 0x0 Channel: 0x1 Number: 0x0 Presence: No
Socket: 0x0 Channel: 0x1 Number: 0x1 Presence: No

Detected CISCO IOFPGA
Booting from Primary BIOS
Code Signing Results: 0x0
Booting from Upgrade FPGA
IOFPGA Subsystem Vendor ID 0x1172
FPGA Revision : 0x1000022
FPGA ID : 0x1564687
FPGA Date : 0x20200410
Power Debug Register1 : 0x0
Power Debug Register2 : 0x90027
Reset Cause Register : 0x80000000
Boot Ctrl Register : 0xe0ff
FPGA Update Status : 0x20

Detected CISCO MIFPGA
MIFPGA Subsystem Vendor ID 0x1172
MIFPGA Version : 0x10
MIFPGA Date : 0x20170515
MIFPGA Update Status : 0x20
MIFPGA ID : 0x1555231

Board Type: SUMPIN

Bootable Disk is detected. Device Name: INTEL SSDSCKKB240G8K
Version 2.18.1260. Copyright (C) 2020 American Megatrends, Inc.

Is there any way to fix this?

Thanks in advance!

 

 

0 Replies 0