05-19-2020 02:09 PM
I Have a 3850 48T, via USB iv upgraded to the latest IOS and all weht well except this as below notes
-notice with upgrade install
Warning! - some ng3k filesystems may not have unmounted cleanly...
-boot loop msg after reboot, cant access it even no luck with the mode mode button
ABNORMAL_RESET_COUNT=0
BOOT=flash:packages.conf
BSI=0
CFG_MODEL_NUM=WS-C3850-48T-S
CLEI_CODE_NUMBER=IPMW800ARB
DEFAULT_ROUTER=10.1.1.1
ECI_CODE_NUMBER=466863
EI_NOPROG=1
IP_ADDR=10.1.1.15/255.255.255.0
LINUX_CMDLINE=rw console=ttyS0,9600,n8
LINUX_COREMASK=15
MAC_ADDR=1C:E8:5D:52:C8:80
MANUAL_BOOT=no
MODEL_NUM=WS-C3850-48T
MODEL_REVISION_NUM=R0
MOTHERBOARD_ASSEMBLY_NUM=73-14444-07
MOTHERBOARD_REVISION_NUM=A0
MOTHERBOARD_SERIAL_NUM=FOC184696XA
RECOVERY_BUNDLE=sda9:cat3k_caa-recovery.bin
STKPWR_ASSEMBLY_NUM=73-11956-08
STKPWR_REVISION_NUM=A0
STKPWR_SERIAL_NUM=FOC18466CWS
SYSTEM_SERIAL_NUM=FCW1847C0JT
TAN_NUM=800-37552-03
TAN_REVISION_NUMBER=A0
TEMPLATE=advanced
TERMLINES=0
USB_ASSEMBLY_NUM=73-12923-05
USB_REVISION_NUM=C0
USB_SERIAL_NUM=FOC18467ZJ5
VERSION_ID=V04
BAUD=9600
SWITCH_NUMBER=1
RANDOM_NUM=335699342
05-19-2020 03:01 PM
Let's wait for experts but I think you have to go back. check flash if there is still previous version; if yes, change BOOT=flash: xxx . if not, copy previous .bin file to flash and boot from it.
Regards, ML
**Please Rate All Helpful Responses **
05-26-2020 12:16 PM
Hi. the switch say the follow in repeat till a certain point then it stops looping but still unable to access anything even by holder the node button when powering up or even when power up already, tried holding it for a long time. The following is all I have:
▒▒▒▒▒▒▒▒▒▒▒▒▒▒ABNORMAL_RESET_COUNT=0
BOOT=flash:packages.conf
BSI=0
CFG_MODEL_NUM=WS-C3850-48T-S
CLEI_CODE_NUMBER=IPMW800ARB
DEFAULT_ROUTER=10.1.1.1
ECI_CODE_NUMBER=466863
EI_NOPROG=1
IP_ADDR=10.1.1.15/255.255.255.0
LINUX_CMDLINE=rw console=ttyS0,9600,n8
LINUX_COREMASK=15
MAC_ADDR=1C:E8:5D:52:C8:80
MANUAL_BOOT=no
MODEL_NUM=WS-C3850-48T
MODEL_REVISION_NUM=R0
MOTHERBOARD_ASSEMBLY_NUM=73-14444-07
MOTHERBOARD_REVISION_NUM=A0
MOTHERBOARD_SERIAL_NUM=FOC184696XA
RECOVERY_BUNDLE=sda9:cat3k_caa-recovery.bin
STKPWR_ASSEMBLY_NUM=73-11956-08
STKPWR_REVISION_NUM=A0
STKPWR_SERIAL_NUM=FOC18466CWS
SYSTEM_SERIAL_NUM=FCW1847C0JT
TAN_NUM=800-37552-03
TAN_REVISION_NUMBER=A0
TEMPLATE=advanced
TERMLINES=0
USB_ASSEMBLY_NUM=73-12923-05
USB_REVISION_NUM=C0
USB_SERIAL_NUM=FOC18467ZJ5
VERSION_ID=V04
BAUD=9600
SWITCH_NUMBER=1
RANDOM_NUM=335699342
09-27-2022 08:54 AM
Hey, Did you ever find a solution to this issue? I have the exact same issue now and I can't get to a point where I can enter anythign into the switch at all. It just keep cycling 5 times through these messages and then locks up.
09-27-2022 04:13 PM
Console into the switch and reboot.
Post the entire boot-up process.
05-19-2020 03:37 PM
05-26-2020 12:18 PM - edited 05-26-2020 12:20 PM
The switch seems locked up and if I reboot it just repeat again the msges in boot still it stop. All the status lights on the left on constantly as well
05-26-2020 04:26 PM
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: