12-21-2016 01:38 PM
Hello,
I just installed c800-universalk9_iox-mz.SPA.156-2.T.bin to support iox on my 819 4G router. Everything seems fine but I find some strange information in iox show commands, see under "Network Information" -> default gateway and mask:
show iox detail
IOx Infrastructure Summary:
---------------------------
Services State : OK
Networking Configured : OK
IOS Network Reachable : OK
Host Infrastructure State : OK
System Information:
-------------------
Build Date : Tue Jul 21 11:12:41 PDT 2015
Version : cwan_mizuno_dev/109
Uptime : 3d 8h 19m 45s
Disk Space Usage : 32% (309MB)
Memory Usage : 38% (193MB)
CPU Utilization : 1%
Networking Information:
-----------------------
IP Address : 10.10.98.2
IP Gateway : 255.255.255.0
IP Netmask : 10.10.98.1
IOx Host Agent:
---------------
Debug Level : WARNING
IOx Processes State:
--------------------
caf : Running
crond : Running
ioxhad : Running
libvirtd : Running
monit : Running
I can reach the web-interface on 10.10.98.2 but when I try to run ioxclient commands towards it I get error 404. Running iox on ubuntu 14.04.
So I tried to upgrade my iox firmware to "p1021_c800.V1.0.0.20.bin.zip" but then I get this from my show commands:
show run | section iox
iox
host ip address 10.10.98.2 255.255.255.0
host ip default-gateway 10.10.98.1
host boot flash:p1021_c800.V1.0.0.20.bin
-----------------------------------------------------------------------------
show iox detail
IOx Infrastructure Summary:
---------------------------
Services State : FAIL
Networking Configured : OK
IOS Network Reachable : OK
Host Infrastructure State : FAIL
System Information:
-------------------
Build Date : Wed Feb 17 20:41:26 PST 2016
Version : cwan_mizuno_dev_v156_1_t_throt/57
Uptime : 0d 0h 4m 34s
Disk Space Usage : 32% (309MB)
Memory Usage : 40% (202MB)
CPU Utilization : 2%
Networking Information:
-----------------------
IP Address : 10.10.98.2
IP Gateway : 255.255.255.0
IP Netmask : 10.10.98.1
IOx Host Agent:
---------------
Debug Level : WARNING
IOx Processes State:
--------------------
caf : Not Running
crond : Running
ioxhad : Running
libvirtd : Running
monit : Running
Anyone have any idea or experience about this behavior?
Thanks!
Oscar
12-22-2016 10:51 AM
Hi Oscar,
Looks like gateway and netmask are swapped in "show iox detail" output. I can reproduce this symptom in the lab. This is a display issue, network interface and routing table entry on IOx host are configured properly.
Could you try upgrading the IOS image to 156-1.T1? It is embedded with a newer version of IOx image.
Please remove "host boot flash:p1021_c800.V1.0.0.20.bin" from configuration before you reload the router.
-Ting
12-23-2016 04:16 AM
Hi,
Where can I find 156-1.T1?
I only have access to the file area here on devnet community and the only image available here is the 156-2.T for 819 platform.
Thanks
Oscar
12-26-2016 10:08 PM
To get the 15.6.1T1, please go to CCO below for downloading.
https://software.cisco.com/download/special/release.html?config=5d86ddfef03e0be6da411eb08d75cfd7
12-27-2016 12:09 AM
Unfortunetly I don't have support contract for this device, I can only download images from the "restricted" section here on devnet. .../docs/DOC-68539.
And there you only have the "c800-universalk9_iox-mz.SPA.156-2.T.bin." version.
Could you add 15.6.1T1 to there?
Best regards
Oscar
03-05-2017 08:01 PM
Hi Steve,
I am also facing the same issue with the Iox. The gateway and netmask are swapped when I run 'sh iox detail' but the configuration seems to be normal.
I have booted the device with c800-universalk9_iox-mz.SPA.156-1.T1.bin image but unable to access Iox interface.
anyone have any idea about this behaviour?
Thanks,
Srikanth
03-01-2017 11:15 PM
Hi Ting,
I am also facing the same issue with the Iox. The gateway and netmask are swapped when I run 'sh iox detail' but the configuration seems to be normal.
I have booted the device with c800-universalk9_iox-mz.SPA.156-1.T1.bin image but unable to access Iox interface.
anyone have any idea about this behaviour?
Thanks,
Srikanth
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community: