cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
3024
Views
1
Helpful
6
Replies

Problem with iox firmware

CSCO12103188
Beginner
Beginner

Hello,

I just installed c800-universalk9_iox-mz.SPA.156-2.T.bin to support iox on my 819 4G router. Everything seems fine but I find some strange information in iox show commands, see under "Network Information" -> default gateway and mask:

show iox detail

IOx Infrastructure Summary:

---------------------------

Services State                 : OK

Networking Configured          : OK

IOS Network Reachable          : OK

Host Infrastructure State      : OK

System Information:

-------------------

Build Date                     : Tue Jul 21 11:12:41 PDT 2015

Version                        : cwan_mizuno_dev/109

Uptime                         : 3d 8h 19m 45s

Disk Space Usage               : 32% (309MB)

Memory Usage                   : 38% (193MB)

CPU Utilization                : 1%

Networking Information:

-----------------------

IP Address                     : 10.10.98.2

IP Gateway                     : 255.255.255.0

IP Netmask                     : 10.10.98.1

IOx Host Agent:

---------------

Debug Level                    : WARNING

IOx Processes State:

--------------------

caf                            : Running

crond                          : Running

ioxhad                         : Running

libvirtd                       : Running

monit                          : Running


I can reach the web-interface on 10.10.98.2 but when I try to run ioxclient commands towards it I get error 404. Running iox on ubuntu 14.04.

So I tried to upgrade my iox firmware to "p1021_c800.V1.0.0.20.bin.zip" but then I get this from my show commands:

show run | section iox

iox

host ip address 10.10.98.2 255.255.255.0

host ip default-gateway 10.10.98.1

host boot flash:p1021_c800.V1.0.0.20.bin

-----------------------------------------------------------------------------

show iox detail


IOx Infrastructure Summary:

---------------------------

Services State                 : FAIL

Networking Configured          : OK

IOS Network Reachable          : OK

Host Infrastructure State      : FAIL

System Information:

-------------------

Build Date                     : Wed Feb 17 20:41:26 PST 2016

Version                        : cwan_mizuno_dev_v156_1_t_throt/57

Uptime                         : 0d 0h 4m 34s

Disk Space Usage               : 32% (309MB)

Memory Usage                   : 40% (202MB)

CPU Utilization                : 2%

Networking Information:

-----------------------

IP Address                     : 10.10.98.2

IP Gateway                     : 255.255.255.0

IP Netmask                     : 10.10.98.1

IOx Host Agent:

---------------

Debug Level                    : WARNING

IOx Processes State:

--------------------

caf                            : Not Running

crond                          : Running

ioxhad                         : Running

libvirtd                       : Running

monit                          : Running

Anyone have any idea or experience about this behavior?

Thanks!

Oscar


6 Replies 6

tyu@cisco.com
Cisco Employee
Cisco Employee

Hi Oscar,

Looks like gateway and netmask are swapped in "show iox detail" output. I can reproduce this symptom in the lab. This is a display issue, network interface and routing table entry on IOx host are configured properly.

Could you try upgrading the IOS image to 156-1.T1? It is embedded with a newer version of IOx image.

Please remove "host boot flash:p1021_c800.V1.0.0.20.bin" from configuration before you reload the router.


-Ting

Hi,

Where can I find 156-1.T1?

I only have access to the file area here on devnet community and the only image available here is the 156-2.T for 819 platform.

Thanks

Oscar

Unfortunetly I don't have support contract for this device, I can only download images from the "restricted" section here on devnet. .../docs/DOC-68539.

And there you only have the "c800-universalk9_iox-mz.SPA.156-2.T.bin." version.

Could you add 15.6.1T1 to there?

Best regards

Oscar

Hi Steve,

I am also facing the same issue with the Iox. The gateway and netmask are swapped when I run 'sh iox detail' but the configuration seems to be normal.

I have booted the device with c800-universalk9_iox-mz.SPA.156-1.T1.bin image but unable to access Iox interface.

anyone have any idea about this behaviour?

Thanks,

Srikanth

Hi Ting,

I am also facing the same issue with the Iox. The gateway and netmask are swapped when I run 'sh iox detail' but the configuration seems to be normal.

I have booted the device with c800-universalk9_iox-mz.SPA.156-1.T1.bin image but unable to access Iox interface.

anyone have any idea about this behaviour?

Thanks,

Srikanth

Getting Started

Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:

Recognize Your Peers