cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1142
Views
0
Helpful
1
Replies

ASA 5512-X set speed & Duplex - HELP

Joseph Mwangi
Level 1
Level 1

Hello Team, 

Iam getting a gig fiber circuit to a fiber interface gigabit 1/0- I do not see an option where i can set speed and duplex on any of the interfaces. The ISP is asking me set speed to GIG full.

Currently, they are giving me a 300MB copper handoff 

new interface 1GB interface detail

MY-ASA# show interface outsideNew
Interface GigabitEthernet1/0 "outsideNEW", is administratively down, line protocol is down
Hardware is i82576F rev01, BW 1000 Mbps, DLY 10 usec
Input flow control is unsupported, output flow control is off
MAC address 00e0.ed27.37cc, MTU 1500
IP address unassigned
1642 packets input, 125143 bytes, 0 no buffer
Received 0 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 pause input, 0 resume input
0 L2 decode drops
1 packets output, 64 bytes, 0 underruns
0 pause output, 0 resume output
0 output errors, 0 collisions, 1 interface resets
0 late collisions, 0 deferred
22 input reset drops, 0 output reset drops
Traffic Statistics for "outsideNEW":
1620 packets input, 88858 bytes
1 packets output, 28 bytes
1620 packets dropped
1 minute input rate 0 pkts/sec, 0 bytes/sec
1 minute output rate 0 pkts/sec, 0 bytes/sec
1 minute drop rate, 0 pkts/sec
5 minute input rate 0 pkts/sec, 0 bytes/sec
5 minute output rate 0 pkts/sec, 0 bytes/sec
5 minute drop rate, 0 pkts/sec

Existing 300MB interface detail


MY-ASA# show interface outside
Interface GigabitEthernet0/1 "outside", is up, line protocol is up
Hardware is i82574L rev00, BW 1000 Mbps, DLY 10 usec
Auto-Duplex(Full-duplex), Auto-Speed(1000 Mbps)
Input flow control is unsupported, output flow control is off
MAC address fc99.4749.f368, MTU 1500
IP address IP.IP.IP.IP subnet mask 255.255.255.252
189881782 packets input, 83840520803 bytes, 0 no buffer
Received 54 broadcasts, 0 runts, 0 giants
0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
0 pause input, 0 resume input
0 L2 decode drops
196329111 packets output, 43697159352 bytes, 0 underruns
0 pause output, 0 resume output
0 output errors, 0 collisions, 2 interface resets
0 late collisions, 0 deferred
0 input reset drops, 0 output reset drops
input queue (blocks free curr/low): hardware (492/362)
output queue (blocks free curr/low): hardware (457/266)
Traffic Statistics for "outside":
189880168 packets input, 80233022472 bytes
196329111 packets output, 39884612900 bytes
549580 packets dropped
1 minute input rate 4026 pkts/sec, 2510172 bytes/sec
1 minute output rate 3796 pkts/sec, 1112023 bytes/sec
1 minute drop rate, 5 pkts/sec

Am i missing something 

1 Reply 1

syeda3
Level 1
Level 1

Please refer to the below url which might be helpful to answer your question.

http://www.cisco.com/c/en/us/support/docs/security/asa-5500-x-series-next-generation-firewalls/113393-asa-troubleshoot-throughput-00.html#interface

http://www.cisco.com/c/en/us/td/docs/security/asa/asa92/asdm72/general/asa-general-asdm/interface-basic.pdf

Hope to help.

Review Cisco Networking for a $25 gift card