Buy or Renew
Buy or Renew

Network Security

Engage with peers and experts on network security topics such as Secure Firewall Threat Defense, Adaptive Security Appliance, Secure Firewall Management Center, and Security Cloud Control.
cancel
Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for 
Search instead for 
Did you mean: 
cancel
Start a conversation

“Join

 
Labels

Forum Posts

Start a conversation

Resolved! Outbound NAT for one Port Only

Hi All,I have a Cisco ASA 5510 and would like to setup a NAT rule for one server but only for traffic that matches a destination with a specific IP and Port. Is this possible? The reason I ask is because I have one application that requires a connect...

Resolved! ASA IPv6 Static Command Equivalent

Hi guys, I am implementing IPv6 on a lab environment.  My ASA is running 8.2(5).  I am mapping the outside IP address 66.181.12.242 to 192.168.22.101 with the following command:static (inside,outside) 66.181.12.242 192.168.22.101 netmask 255.255.255....

jmunoz19 by • Level 4
  • 670 Views
  • 1 replies
  • 0 Helpful votes

Resolved! nonat access-list versus static mapping

I am using code level 8.2.5 global (dmz) 1 interfaceglobal (outside) 1 interfacenat (dmz) 0 access-list NONAT1nat (inside) 0 access-list nonatstatic (inside,dmz) 10.42.198.176 172.22.196.2 netmask 255.255.255.255 This is in reference to the bold nat ...

gp1200x by • Level 2
  • 712 Views
  • 2 replies
  • 0 Helpful votes

Resolved! Lost Pending Certificate Request

Hi,I have completed the Certificate Request from the ASA ASDM GUI and forgot to save before closing (Saved only from command line) which apparently does not save what has been done from the ASDM. Now I have received the certificate from the CA but ha...

Resolved! mac-address auto

hi all,i'm going to configure an ASA for multiple security context and ran into this command.http://www.cisco.com/c/en/us/td/docs/security/asa/asa82/command/reference/cmd_ref/m.html#wp2043127the design would be the 'outside' interface G0/0 will be sh...

Resolved! ASA active/standby with single link to ISP

 Hi Everyone, For learning purposes at my home lab i have 2 ASA.They have active/standby feature.Currently single ASA has uplink connection to ISP modem.This ASA has 2 interfaces going to 2 different switches.Need to know if i configure second ASA wi...

mahesh18 by • Level 6
  • 580 Views
  • 2 replies
  • 0 Helpful votes

Resolved! sh conn flag -

 Hi everyone, i ran the commandASA1# sh conn address 10.0.0.218 in use, 567 most usedUDP outside  128.100.56.135:123 inside  10.0.0.2:123, idle 0:01:01, bytes 21312, flags - ASA1# sh conn address 10.0.0.222 in use, 567 most usedUDP outside  128.100.5...

mahesh18 by • Level 6
  • 1781 Views
  • 4 replies
  • 0 Helpful votes

Resolved! ASA 8.4 Active/Standby issue

Hi,Have configured Active/Standby and configuration has been copied fine from one device to other. All interfaces that have been auto created (to match the original device) are showing IP addresses correctly (UP,UP) The ASA are connected via 2 switch...

Resolved! ASA 5585 - multi context clustering

Good Morning,    I have an one ASA 5585  in multi context mode ( 18 context present). I would like to add an other ASA to do a cluster.  I would to have an Actif/Passif cluster .Do i have to change configuration on all contexts ?If anybody can help m...

Load more
Review Cisco Networking for a $25 gift card