cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
Announcements

2564
Views
0
Helpful
3
Replies
ejeangilles
Beginner

Can't create subinteface on Cisco ASA 5505?

I have a Cisco 5505 with a security plus license and but I can’t seem to create sub interfaces on it.

ASA1(config)# sh ver

Cisco Adaptive Security Appliance Software Version 8.2(2)4
Device Manager Version 6.0(3)

Compiled on Wed 03-Feb-10 14:17 by builders
System image file is “disk0:/asa822-4-k8.bin”
Config file at boot was “startup-config”

ASA1 up 1 day 18 hours

Hardware: ASA5505, 512 MB RAM, CPU Geode 500 MHz
Internal ATA Compact Flash, 128MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024KB

Encryption hardware device : Cisco ASA-5505 on-board accelerator (revision 0×0)
Boot microcode : CN1000-MC-BOOT-2.00
SSL/IKE microcode: CNLite-MC-SSLm-PLUS-2.03
IPSec microcode : CNlite-MC-IPSECm-MAIN-2.04
0: Int: Internal-Data0/0 : address is d0d0.fd30.5df5, irq 11
1: Ext: Ethernet0/0 : address is d0d0.fd30.5ded, irq 255
2: Ext: Ethernet0/1 : address is d0d0.fd30.5dee, irq 255
3: Ext: Ethernet0/2 : address is d0d0.fd30.5def, irq 255
4: Ext: Ethernet0/3 : address is d0d0.fd30.5df0, irq 255
5: Ext: Ethernet0/4 : address is d0d0.fd30.5df1, irq 255
6: Ext: Ethernet0/5 : address is d0d0.fd30.5df2, irq 255
7: Ext: Ethernet0/6 : address is d0d0.fd30.5df3, irq 255
8: Ext: Ethernet0/7 : address is d0d0.fd30.5df4, irq 255
9: Int: Internal-Data0/1 : address is 0000.0003.0002, irq 255
10: Int: Not used : irq 255
11: Int: Not used : irq 255

Licensed features for this platform:
Maximum Physical Interfaces : 8
VLANs : 20, DMZ Unrestricted
Inside Hosts : 50
Failover : Active/Standby
VPN-DES : Enabled
VPN-3DES-AES : Enabled
SSL VPN Peers : 2
Total VPN Peers : 25
Dual ISPs : Enabled
VLAN Trunk Ports : 8
Shared License : Disabled
AnyConnect for Mobile : Disabled
AnyConnect for Cisco VPN Phone : Disabled
AnyConnect Essentials : Disabled
Advanced Endpoint Assessment : Disabled
UC Phone Proxy Sessions : 2
Total UC Proxy Sessions : 2
Botnet Traffic Filter : Disabled

This platform has an ASA 5505 Security Plus license.
This is what I get when trying to add a subinterface

ASA1(config)# int e0/2.120
                         ^
ERROR: % Invalid input detected at ‘^’ marker.

Any suggestions would be helpful

1 ACCEPTED SOLUTION

Accepted Solutions
craig bache
Beginner

Hi Edwin

Please see the following for the 5505,

http://www.cisco.com/en/US/docs/security/asa/asa82/configuration/guide/intrface.html#wp1072137

You assign each switch port to a VLAN interface or have a trunk interface for multiple VLAN's.

Please rate if this helps

Craig

View solution in original post

3 REPLIES 3
craig bache
Beginner

Hi Edwin

Please see the following for the 5505,

http://www.cisco.com/en/US/docs/security/asa/asa82/configuration/guide/intrface.html#wp1072137

You assign each switch port to a VLAN interface or have a trunk interface for multiple VLAN's.

Please rate if this helps

Craig

View solution in original post

Hi Edwin,

ASA5505 does not support subintercface (as the ports are switch ports). Please check the below  discussion as well.

https://supportforums.cisco.com/thread/227029

hth

MS

Thanks it worked.