08-26-2010 02:58 PM - edited 03-11-2019 11:31 AM
Hello.
I configured EIGRP between a Switch 3550 and an ASA-5505., The session of neighbors work without problems, but no EIGRP routes are exchanged.
I try change the nameif and the security level but it still does not work ...
************************************************************************************************
ASA5505# sh ver
Cisco Adaptive Security Appliance Software Version 8.0(2)
Device Manager Version 6.1(5)
************************************************************************************************
Configuration ASA-5505
!
interface Vlan2
description $---> OUTSIDE SW-3550 <---$
nameif OUTSIDE
security-level 0
ip address 10.100.100.86 255.255.255.252
!
router eigrp 10
no auto-summary
network 10.0.0.0 255.0.0.0
ASA5505# sh eigrp neighbors
EIGRP-IPv4 neighbors for process 10
H Address Interface Hold Uptime SRTT RTO Q Seq
(sec) (ms) Cnt Num
0 10.241.3.85 Vl2 10 00:00:04 1 3000 2 0
ASA5505#
ASA5505# show route
Codes: C - connected, S - static, I - IGRP, R - RIP, M - mobile, B - BGP
D - EIGRP, EX - EIGRP external, O - OSPF, IA - OSPF inter area
N1 - OSPF NSSA external type 1, N2 - OSPF NSSA external type 2
E1 - OSPF external type 1, E2 - OSPF external type 2, E - EGP
i - IS-IS, L1 - IS-IS level-1, L2 - IS-IS level-2, ia - IS-IS inter area
* - candidate default, U - per-user static route, o - ODR
P - periodic downloaded static route
Gateway of last resort is 10.100.100.85 to network 0.0.0.0
C 19.16.0.24 255.255.255.252 is directly connected, DMZ3
C 127.1.0.0 255.255.0.0 is directly connected, _internal_loopback
C 10.41.3.252 255.255.255.252 is directly connected, DMZ1
C 10.100.100.84 255.255.255.252 is directly connected, OUTSIDE
S* 0.0.0.0 0.0.0.0 [1/0] via 10.100.100.85, OUTSIDE
ASA5505#
Solved! Go to Solution.
08-26-2010 03:15 PM
See if this applies in your case:
CSCsk61945 ASA incompatible with routers using EIGRP version 3
resolved in 8.0.2.(21)
Symptom:
EIGRP routes are not installed on the ASA nor the neighbor.
Conditions:
This occurs when the IOS Router is running software with EIGRP version 3.0
or higher. The version of the IOS neighbor can be checked via the
"show eigrp neighbor detail" command.
Workaround:
If possible, downgrade to an IOS release which uses the older version
of EIGRP.
-KS
08-26-2010 03:15 PM
See if this applies in your case:
CSCsk61945 ASA incompatible with routers using EIGRP version 3
resolved in 8.0.2.(21)
Symptom:
EIGRP routes are not installed on the ASA nor the neighbor.
Conditions:
This occurs when the IOS Router is running software with EIGRP version 3.0
or higher. The version of the IOS neighbor can be checked via the
"show eigrp neighbor detail" command.
Workaround:
If possible, downgrade to an IOS release which uses the older version
of EIGRP.
-KS
08-26-2010 03:48 PM
thanks! .. I update the ASA's operating system and works well!:.
08-26-2010 03:50 PM
Wow ! That was quick. Glad to hear. Thanks for rating.
-KS
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide