Hi.
I have a problem with failover. On My site I have 2 Firewalls 5580. And I did this configuration on my firewall.
interface GigabitEthernet3/0
description LAN/STATE Failover Interface
speed nonegotiate
failover
failover lan unit secondary
failover lan interface failover+stateful GigabitEthernet3/0
failover polltime unit 1 holdtime 10
failover polltime interface 2 holdtime 10
failover key *****
failover replication http
failover link failover+stateful GigabitEthernet3/0
failover interface ip failover+stateful 10.215.253.181 255.255.255.252 standby 10.215.253.182
I want to monitoring one interface but when I put this interface on monitoring the interface still in waiting state..
pri/act/MZ-IT-C1-FW-013-A# sh failover
Failover On
Failover unit Primary
Failover LAN Interface: failover+stateful GigabitEthernet3/0 (up)
Unit Poll frequency 1 seconds, holdtime 10 seconds
Interface Poll frequency 2 seconds, holdtime 10 seconds
Interface Policy 1
Monitored Interfaces 3 of 256 maximum
failover replication http
Version: Ours 8.2(3), Mate 8.2(3)
Last Failover at: 02:36:03 HoVerao Oct 26 2011
This host: Primary - Active
Active time: 10799820 (sec)
slot 0: ASA5580 hw/sw rev (1.0/8.2(3)) status (Up Sys)
Interface noc (10.215.113.55): Normal (Not-Monitored)
Interface soc (10.215.128.4): Normal (Not-Monitored)
Interface bovespa (10.215.252.108): Normal (Not-Monitored)
Interface cma (10.215.252.116): Normal (Not-Monitored)
Interface insidecam1 (10.215.253.201): Normal (Waiting)
Interface corp (10.215.253.84): Normal
Interface outside (10.215.253.140): Normal
Other host: Secondary - Standby Ready
Active time: 257330 (sec)
slot 0: ASA5580 hw/sw rev (1.0/8.2(3)) status (Up Sys)
Interface noc (10.215.113.56): Normal (Not-Monitored)
Interface soc (10.215.128.5): Normal (Not-Monitored)
Interface bovespa (10.215.252.109): Normal (Not-Monitored)
Interface cma (10.215.252.117): Normal (Not-Monitored)
Interface insidecam1 (10.215.253.202): Normal
Interface corp (10.215.253.85): Normal
Interface outside (10.215.253.141): Normal
Stateful Failover Logical Update Statistics
Link : failover+stateful GigabitEthernet3/0 (up)
Stateful Obj xmit xerr rcv rerr
General 37311057710 0 5846984 288020467
sys cmd 1474140 0 1474137 0
up time 0 0 0 0
RPC services 0 0 0 0
TCP conn 36211969608 0 865236 280261214
UDP conn 1001804778 0 220454 7757354
ARP tbl 95809184 0 3287157 1899
Xlate_Timeout 0 0 0 0
IPv6 ND tbl 0 0 0 0
VPN IKE upd 0 0 0 0
VPN IPSEC upd 0 0 0 0
VPN CTCP upd 0 0 0 0
VPN SDI upd 0 0 0 0
VPN DHCP upd 0 0 0 0
SIP Session 0 0 0 0
Logical Update Queue Information
Cur Max Total
Recv Q: 0 11 6106431
Xmit Q: 0 2 37321869413
What could be the couse of this issue?
If someone help me with this case, I'll be very grateful.
Thank you very much.
