cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
1579
Views
0
Helpful
2
Replies

fwsm boot problem

russsline
Level 1
Level 1

Hi,

yesterday, after succesfull upgrade FWSM from c6svc-fwm-k9.2-3-4.bin to c6svc-fwm-k9.3-1-3.bin the module did not start.

#show module 1

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 6 Firewall Module WS-SVC-FWM-1 SAD10260AP6

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0018.19ed.f580 to 0018.19ed.f587 4.0 7.2(1) 8.5(0.46)RFW Other

Mod Online Diag Status

---- -------------------

1 Unknown

#hw-module module 1 reset cf:1

Device BOOT variable for reset = <cf:1>

Warning: Device list is not verified.

Proceed with reload of module?[confirm]

% reset issued for module 1

xxxxxxx#

Dec 13 08:54:34.906 MET: SP: The PC in slot 1 is shutting down. Please wait ...

Dec 13 08:54:34.954 MET: %C6KPWR-SP-4-DISABLED: power to module in slot 1 set off (Module Failed SCP dnld)

Dec 13 08:54:39.906 MET: SP: shutdown_pc_process:No response from module 1

Dec 13 08:54:39.906 MET: %SM-SP-4-BADEVENT: Event 'pc_powered_off' is invalid for the current state 'stay_disabled': cygnus_oir_bay slot1

-Traceback= 404D17AC 404C8440 40497618 4027AAD0 4027AABC

Dec 13 08:54:39.906 MET: SP: Last transition recorded: (disabled)-> stay_disabled (operator_power_on)-> can_power_on (yes_power)-> powered_on (yes_power)-> check_power_on (timer)-> check_power_on (power_on_ok)-> wait_til_online (powered_off)-> shutdown_pc (disabled)-> disabled (disabled)-> disabled2 (disabled)-> stay_disabled

show module 1

Mod Ports Card Type Model Serial No.

--- ----- -------------------------------------- ------------------ -----------

1 6 Firewall Module WS-SVC-FWM-1 SAD10260AP6

Mod MAC addresses Hw Fw Sw Status

--- ---------------------------------- ------ ------------ ------------ -------

1 0018.19ed.f580 to 0018.19ed.f587 4.0 7.2(1) 8.5(0.46)RFW PwrDown

Mod Online Diag Status

---- -------------------

1 Not Applicable

After power enable module 1 the situation repeat.

show ver

Cisco Internetwork Operating System Software

IOS (tm) s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF4, RELEASE SOFTWARE (fc1)

Technical Support: http://www.cisco.com/techsupport

Copyright (c) 1986-2006 by cisco Systems, Inc.

Compiled Thu 23-Mar-06 20:33 by tinhuang

Image text-base: 0x40101040, data-base: 0x42DA8000

ROM: System Bootstrap, Version 12.2(17r)S4, RELEASE SOFTWARE (fc1)

BOOTLDR: s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(18)SXF4, RELEASE SOFTWARE (fc1)

thanks for adviced

2 Replies 2

borakcisco
Level 1
Level 1

I suposse that you have solved it already, but the solution is:

- Enter in maintenance partition (cf:1)

- Update version fron here in the correct partion (cf:4 or cf:5)

- Reload the module

From the MP:

upgrade ftp://ftp_username:ftp_password@ip_ftp_server/c6svc-fwm-k9.3-2-1.bin cf:4

regards.

mcrichard
Level 1
Level 1

Hi Sir,

I got same problem.

Do you already resolved it ?

Review Cisco Networking for a $25 gift card