IPS session 1 Password

[shahid_duet]

Dear boss

I have a new ASA5520 with AIP SSM-20. i just configure IP at all interface. now i want to enable SSM- by using session 1 command. but password cisco

dont take.

How i reset pasword ? any other password here ?

how to enable SSM -20

Please sugggest me .

shahid

[varrao]

Hi Shahid,

if the default username n password of cisco, doesnt work you can reset it by the commmand :

hw-module module password-reset

http://www.cisco.com/en/US/customer/docs/security/asa/asa82/command/reference/gh.html#wp1756348

Hope this helps

Thanks,

Varun

[shahid_duet]

Rao

no command as Hw-module module password reset.

your link is not correst. if i click here no page appear .

[varrao]

Hi Shahid,

First you need to do , show module, lets say you have the IPS in slot 1, so the command would be:

hostname (config)# hw-module module 1 password-reset

Reset the password on module in slot 1? [confirm] y

The command is correct, please check there is a  "-" between password and reset.

Thanks,

Varun

[shahid_duet]

Dear Rao

Please see the follwing  conf. I get no password-reset command .

ciscoasa# show module

Mod Card Type                                    Model              Serial No.

--- -------------------------------------------- ------------------ -----------

  0 ASA 5520 Adaptive Security Appliance         ASA5520            JMX1235L0PX

  1 ASA 5500 Series Security Services Module-20  ASA-SSM-20         JAF1228BPLR

Mod MAC Address Range                 Hw Version   Fw Version   Sw Version

--- --------------------------------- ------------ ------------ ---------------

  0 0022.5597.0be7 to 0022.5597.0beb  2.0          1.0(11)4     7.0(8)

  1 001d.7032.58b7 to 001d.7032.58b7  1.0          1.0(11)4     6.0(4)E1

Mod Status             Data Plane Status

--- ------------------ ---------------------

  0 Up Sys             Not Applicable

  1 Up                 Up

ciscoasa# conf t

ciscoasa(config)# hw

ciscoasa(config)# hw-module mo

ciscoasa(config)# hw-module module 1 pass

ciscoasa(config)# hw-module module 1 pass

ciscoasa(config)# hw-module module 1 ?

exec mode commands/options:

  recover   Configure recovery of this module

  reload    Reload the module

  reset     Reset the module

  shutdown  Shut down the module

ciscoasa(config)# hw-module module 1

[varrao]

Hi Shahid,

If you are using a software image that does not  support the password reset command then the only option seems to be,  re-imaging the module:

http://www.cisco.com/en/US/docs/security/ips/6.1/configuration/guide/cli/cli_system_images.html#wp1230355

Hope this helps,

Thanks,

Varun

[shahid_duet]

Rao

I need IPS-SSM-K9-sys-1.1-a-6.1-1-E1.img.

but i hava no software.

where i get it ? i have search in google . not found.

if u have plz send me

thanaks

[varrao]

You can download it from here:

http://www.cisco.com/cisco/software/release.html?mdfid=282539290&flowid=4415&softwareid=282549758&release=6.1%281%29E1&rellifecycle=&relind=AVAILABLE&reltype=latest

Hope this helps

Thanks,

Varun

[varrao]

But you need to have a valid software download contract for it.

-Varun