cancel
Showing results for 
Search instead for 
Did you mean: 
cancel
783
Views
0
Helpful
1
Replies

Register AP 2702i on Controller 2504

jitesh.mahajan
Level 1
Level 1

Dear Support,

 

I am facing the problem while register a Cisco AP on Cisco Controller.

DHCP server i am created on Controller 2504 and Access Point 2702i gets the IP add. from controller DHCP.

But access point is not register on Controller.

AP showing the below error message.

 

*Jan  1 18:25:02.999: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan  1 18:23:58.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.10 peer_port: 5246

*Jan  1 18:24:27.999: DTLS_CLIENT_ERROR: ../capwap/base_capwap/dtls/base_capwap_dtls_connection_db.c:2176 Max retransmission count reached!
*Jan  1 18:24:57.999: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.10:5246
*Jan  1 18:24:57.999: %SYS-3-MGDTIMER: Uninitialized timer, timer stop, timer = 3AFD270. -Process= "CAPWAP CLIENT", ipl= 0, pid= 73
-Traceback= 119AF80z 12A89C8z 12AA11Cz 16F512Cz 17645ECz 16FF088z 172810Cz 17299B4z 1720150z 1720228z 17204ECz 1717E50z 172F6A0z 173075Cz 1324C90z 1309B58z
*Jan  1 18:24:57.999: %LWAPP-3-CLIENTERRORLOG: LWAPP LED Init: incorrect led state 255
*Jan  1 18:24:57.999: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg

*Jan  1 18:24:57.999: %CAPWAP-3-ERRORLOG: Failed to load configuration from flash. Resetting to default config
*Jan  1 18:24:58.007: %LWAPP-3-CLIENTERRORLOG: Config load from flash failed. Initialising Cfg

*Jan  1 18:24:58.007: %IP-3-DESTHOST: src=192.168.1.51, dst=0.0.0.0, NULL desthost -Process= "CAPWAP CLIENT", ipl= 0, pid= 73
-Traceback= 119AF80z 13A3634z 13A4218z 13A4974z 13A49D0z 1331508z 16F0720z 16F681Cz 173D800z 1727CB8z 173B760z 1714110z 17281E8z 17299B4z 1720150z 1720228z
*Jan  1 18:25:08.007: %CAPWAP-3-ERRORLOG: Go join a capwap controller
*Jan  1 18:26:13.000: %CAPWAP-5-DTLSREQSEND: DTLS connection request sent peer_ip: 192.168.1.10 peer_port: 5246
*Jan  1 18:26:13.099: %PKI-3-CERTIFICATE_INVALID_NOT_YET_VALID: Certificate chain validation has failed.  The certificate (SN: 56AB81850000001288AB) is not yet valid   Validity period starts on 05:14:26 UTC Aug 7 2014Peer certificate verification failed 001A

*Jan  1 18:26:13.099: %CAPWAP-3-ERRORLOG: Certificate verification failed!
*Jan  1 18:26:13.099: DTLS_CLIENT_ERROR: ../capwap/base_capwap/capwap/base_capwap_wtp_dtls.c:467 Certificate verified failed!
*Jan  1 18:26:13.099: %DTLS-5-SEND_ALERT: Send FATAL : Bad certificate Alert to 192.168.1.10:5246
*Jan  1 18:26:13.099: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 192.168.1.10:5246
*Jan  1 18:26:13.099: %CAPWAP-3-ERRORLOG: Invalid event 40 & state 3 combination.

 

Regards,

Jitesh Mahajan.

 

1 Reply 1

andreaskurz
Level 1
Level 1

Hi Jitesh,

 

I had the same problem with same components.

One simple thing, that solves my problem: check the time on AccessPoint AND Controller.

but... not only check... adjust!

 

regards,

Andreas

Review Cisco Networking for a $25 gift card