- Cisco Community
- Technology and Support
- Networking
- Networking Knowledge Base
- IOS upgrade of 7206 router
- Subscribe to RSS Feed
- Mark as New
- Mark as Read
- Bookmark
- Subscribe
- Printer Friendly Page
- Report Inappropriate Content
- Subscribe to RSS Feed
- Mark as New
- Mark as Read
- Bookmark
- Subscribe
- Printer Friendly Page
- Report Inappropriate Content
12-14-2014 07:28 AM - edited 03-01-2019 05:04 PM
IOS upgrade 7206 router
Follow the steps to upgrade IOS image of 7206 router:-
1 .Delete unwanted files:-
Router#Dir disk2:
Router#Sh bootflash:
Router#delete bootflash:IOS name
Router#delete disk2:IOS name
Router#format bootflash:
2. Router#squeeze. If required. To remove deleted file.
3.To install IOS images.
Router#copy tftp: disk2: c7200p-adventerprisek9-mz.152-4.M7.bin
Router#verify /md5 disk2:c7200p-adventerprisek9-mz.152-4.M7.bin
O/P:-
...............................................................................................
.......................................................
verify /md5 (bootflash:c7200p-kboot-mz.152-4.M7.bin) = 18b953e28eefed3cb0d7deea4374c922
(verify checksum value from cisco site).It should be same.
https://software.cisco.com/download/type.html?mdfid=282188585&catid=268437899
Hold cursor on image it will show md5 checksum value.
4.To install boot loader file.
Router#copy tftp: bootflash: c7200p-kboot-mz.152-4.M7.bin
Router#verify /md5 disk2: c7200p-kboot-mz.152-4.M7.bin
5.To install FPD image:-
Router#copy tftp: disk2: c7200p-fpd-pkg.152-4.M7.pkg
Router#verify /md5 bootflash:c7200p-kboot-mz.152-4.M7.bin
Verify checksum value.
6.Set boot loader image.
Router#Conf t
boot bootldr bootflash:c7200p-kboot-mz.152-4.M7.bin
7.Remove old IOS boot sequence:-
Router#No boot system disk2: c7200p-adventerprisek9-mz.124-15.T8.bin
Set new boot sequence:-
Router#boot system disk2: c7200p-adventerprisek9-mz.152-4.M7.bin
Router#boot system disk2: c7200p-adventerprisek9-mz.124-15.T8.bin
sh bootvar – Check boot variable before reload.
8.Reboot the router to run with new IOS installed in router.
Router#reload
Check after reload:-
sh version
sh bootvar – Check boot variable after reload.
Note:- VSA and NPE-G2 should be detected after IOS and FPD image upgrade.
FPD image upgrade not required if VSA card is not there.
Sh commands;-
Sh version
Sh inventory
Sh diag
sh hw-module all fpd
show upgrade fpd package default
Router#sh diag
Load for five secs: 0%/0%; one minute: 4%; five minutes: 9%
Time source is NTP, *18:44:30.133 IST Sun Dec 7 2014
Slot 0:
VSA IPsec Card Port adapter
Port adapter is analyzed
Port adapter insertion time 00:04:27 ago
EEPROM contents at hardware discovery:
PCB Serial Number : JAF1322ACKF
Hardware Revision : 1.0
Part Number : 73-10220-05
Board Revision : B1
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 0
Product (FRU) Number : C7200-VSA
Version Identifier : V01
Top Assy. Part Number : 68-2578-05
CLEI Code : CNUCAFNAAA
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF C1 8B 4A 41 46 31 33 32 32 41 43 4B 46 40
0x10: 05 0D 41 01 00 82 49 27 EC 05 42 42 31 03 00 81
0x20: 00 00 00 00 04 00 88 00 00 00 00 CB 94 43 37 32
0x30: 30 30 2D 56 53 41 20 20 20 20 20 20 20 20 20 20
0x40: 20 89 56 30 31 20 D9 03 C1 40 CB 87 44 0A 12 05
0x50: C6 8A 43 4E 55 43 41 46 4E 41 41 41 FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
Slot 1:
VAM2+ Encryption/Compression engine, Port adapter
Port adapter is analyzed
Port adapter insertion time 00:04:28 ago
EEPROM contents at hardware discovery:
Hardware Revision : 1.0
PCB Serial Number : JAB1203007T
Part Number : 73-9571-06
Board Revision : A0
RMA Test History : 00
RMA Number : 0-0-0-0
RMA History : 00
Deviation Number : 0
Product (FRU) Number : SA-VAM2+
Version Identifier : V02
Top Assy. Part Number : 68-2288-06
CLEI Code : CNDQASMGAA
EEPROM format version 4
EEPROM contents (hex):
0x00: 04 FF 40 04 B0 41 01 00 C1 8B 4A 41 42 31 32 30
0x10: 33 30 30 37 54 82 49 25 63 06 42 41 30 03 00 81
0x20: 00 00 00 00 04 00 88 00 00 00 00 CB 94 53 41 2D
0x30: 56 41 4D 32 2B 20 20 20 20 20 20 20 20 20 20 20
0x40: 20 89 56 30 32 20 87 44 08 F0 06 C6 8A 43 4E 44
0x50: 51 41 53 4D 47 41 41 FF FF FF FF FF FF FF FF FF
0x60: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
0x70: FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF FF
sh upgrade fpd package default
Load for five secs: 0%/0%; one minute: 2%; five minutes: 7%
Time source is NTP, *18:45:37.189 IST Sun Dec 7 2014
*************************************************************************
This IOS release requires the following default FPD Image Package for
the automatic upgrade of FPD images:
*************************************************************************
Version: 15.2(4)M7
Package Filename: c7200p-fpd-pkg.152-4.M7.pkg
List of card type supported in this package:
Minimal
No. Card Type HW Ver.
---- ------------------ -------
1) VSA 0.0
2) Port-Adaptor 0.0
3) Port-Adaptor 0.0
4) Port-Adaptor 0.0
5) Port-Adaptor 0.0
6) NPE-G2 0.0
7) C7201 0.0
---- ------------------ -------
If VSA card not detected check the physical LED status of slot0 .
a) Check logs: sh logging (IOS incompatible issue logs then check proper all image name should be same).
b) Remove card from slot by power down the router and re insert the card in slot0.
Power on the router and check LED status.
|
Table 1-6 VSA LED |
||
|
Color |
State |
Function |
|
No color |
Off |
Indicates that the VSA is disabled. |
|
Green |
On |
Indicates the VSA is powered up and enabled for operation. |
|
Amber |
On |
Indicates VSA is booting or has encountered errors. |
|
Yellow |
Powering Up |
Indicates that the VSA is powering up, but software initialization has not started yet. |
c) Issue below command and reload the router. If issue still there.
Enabling VSA card. Disable by prepending no commands.
R (config)#crypto engine slot 0
VSA will NOT come up until system power-cycle or reload...
R(config)#crypto engine accelerator 0
VSA will NOT come up until system power-cycle or reload...
R(config)#wr
R(config)#reload
Other O/P for information:-
router#copy tftp: disk2:
Address or name of remote host []? 10.2.11.194
Source filename []? c7200p-fpd-pkg.152-4.M7.pkg
Destination filename [c7200p-fpd-pkg.152-4.M7.pkg]?
Accessing tftp://10.2.11.194/c7200p-fpd-pkg.152-4.M7.pkg...
Loading c7200p-fpd-pkg.152-4.M7.pkg from 10.2.11.194 (via GigabitEthernet0/1): !!!!!!!!!!!!!!
[OK - 3450880 bytes]
3450880 bytes copied in 6.272 secs (550204 bytes/sec)
router#sh hw-module all fpd
Load for five secs: 0%/0%; one minute: 3%; five minutes: 8%
Time source is NTP, *18:44:59.061 IST Sun Dec 7 2014
==== ====================== ====== =============================================
H/W Field Programmable Current Min. Required
Slot Card Type Ver. Device: "ID-Name" Version Version
==== ====================== ====== ================== =========== ==============
npe NPE-G2 1.3 1-NPEG2 I/O FPGA 0.38 0.33
---- ---------------------- ------ ------------------ ----------- --------------
0 VSA 0.4 1-VSA 0.23 0.23
==== ====================== ====== =============================================
router#sh upgrade fpd package default
Load for five secs: 0%/0%; one minute: 2%; five minutes: 7%
Time source is NTP, *18:45:37.189 IST Sun Dec 7 2014
*************************************************************************
This IOS release requires the following default FPD Image Package for
the automatic upgrade of FPD images:
*************************************************************************
Version: 15.2(4)M7
Package Filename: c7200p-fpd-pkg.152-4.M7.pkg
List of card type supported in this package:
Minimal
No. Card Type HW Ver.
---- ------------------ -------
1) VSA 0.0
2) Port-Adaptor 0.0
3) Port-Adaptor 0.0
4) Port-Adaptor 0.0
5) Port-Adaptor 0.0
6) NPE-G2 0.0
7) C7201 0.
router#sh upgrade fpd progress
Load for five secs: 0%/0%; one minute: 3%; five minutes: 7%
Time source is NTP, *18:46:04.469 IST Sun Dec 7 2014
% There is no FPD image upgrade in progress.
router#sh hw-module all fpd
==== ====================== ====== =============================================
H/W Field Programmable Current Min. Required
Slot Card Type Ver. Device: "ID-Name" Version Version
==== ====================== ====== ================== =========== ==============
npe NPE-G2 1.3 1-NPEG2 I/O FPGA 0.38 0.33
---- ---------------------- ------ ------------------ ----------- --------------
0 VSA 0.4 1-VSA 0.19 0.18
==== ====================== ====== =============================================
example;-
Router# show hw-module all fpd
==== ====================== ====== =============================================
H/W Field Programmable Current Min. Required
Slot Card Type Ver. Device: "ID-Name" Version Version
==== ====================== ====== ================== =========== ==============
npe NPE-G2 1.5 1-NPEG2 I/O FPGA 0.18 0.20 *
---- ---------------------- ------ ------------------ ----------- --------------
0 VSA 0.0 1-VSA 0.10 0.10
==== ====================== ====== =============================================
NOTES:
- FPD images that are required to be upgraded are indicated with a '*'
character in the "Minimal Required Version" field.
- The following FPD image package file is required for the upgrade:
"c7200-fpd-pkg.124-4.XD.pkg"
router#show upgrade fpd package default
*************************************************************************
This IOS release requires the following default FPD Image Package for
the automatic upgrade of FPD images:
*************************************************************************
Version: 12.4(15)T8
Package Filename: c7200p-fpd-pkg.124-15.T8.pkg
List of card type supported in this package:
Minimal
No. Card Type HW Ver.
---- ------------------ -------
1) VSA 0.0
2) Port-Adaptor 0.0
3) Port-Adaptor 0.0
4) Port-Adaptor 0.0
5) Port-Adaptor 0.0
6) NPE-G2 0.0
7) C7201 0.0
Useful docs:-
FPD:-
http://www.cisco.com/c/en/us/td/docs/routers/7200/configuration/feature_guides/fpd.html
http://www.cisco.com/c/en/us/td/docs/routers/7200/configuration/feature_guides/fpd.html
VSA:-
http://www.cisco.com/c/en/us/td/docs/security/vpn_modules/vam_vsa/vsa/vsa/vsa_ov.html
The Cisco 7200 series routers have three basic boot images that support different hardware options. The three images are the standard c7200-boot-mz boot image, the c7200-kboot-mz boot image, and the c7200-mboot-mz image. The c7200-kboot-mz image was released in October, 2000 and is larger than the standard c7200-boot-mz image because it supports newer hardware that is not supported in the c7200-boot-mz image.
Find answers to your questions by entering keywords or phrases in the Search bar above. New here? Use these resources to familiarize yourself with the community:
