03-09-2004 07:34 AM - edited 03-09-2019 06:41 AM
PIX newbie here,
I cannot get access to internet through my PIX-503 version 6.3(3)
I can ping from pc, and dhcp assign IP from firewall too, but cannot get out!
I have ISP router cable in port 0 and cable to LAN hub is in port 1.
my router IP (example) 10.0.0.7
my outside gateway ip 10.0.0.22
what is wrong with my config?
interface ethernet0 auto
interface ethernet1 100full
nameif ethernet0 outside security0
nameif ethernet1 inside security100
enable password Password encrypted
passwd Password encrypted
hostname OfficeName
domain-name DomainName.com
fixup protocol dns maximum-length 512
fixup protocol ftp 21
fixup protocol h323 h225 1720
fixup protocol h323 ras 1718-1719
fixup protocol http 80
fixup protocol rsh 514
fixup protocol rtsp 554
fixup protocol sip 5060
fixup protocol sip udp 5060
fixup protocol skinny 2000
fixup protocol smtp 25
fixup protocol sqlnet 1521
fixup protocol tftp 69
names
name insideIP VPNHEADEND
name outsideIP MailServer
name outsideIP .0 HomeOffc
access-list inside_outbound_nat0_acl permit ip insideIP 255.255.255.0 VPNHEADEND 255.255.255.0
access-list outside_cryptomap_20 permit ip insideIP 255.255.255.0 VPNHEADEND 255.255.255.0
access-list outside_access_in permit ip VPNHEADEND 255.255.255.0 any
access-list outside_access_in permit tcp host MailServer any
access-list outside_access_in permit ip HomeOffc 255.255.255.0 host outsideIP
access-list outside_access_in permit ip host 10.0.0.7 any
pager lines 24
logging on
logging timestamp
logging console warnings
logging buffered warnings
logging trap informational
mtu outside 1500
mtu inside 1500
ip address outside 10.0.0.22 255.255.255.xxx
ip address inside insidegatewayIP 255.255.255.0
ip audit info action alarm
ip audit attack action alarm
pdm location insideIP 255.255.255.255 inside
pdm location VPNHEADEND 255.255.255.0 outside
pdm location MailServer 255.255.255.255 outside
pdm location HomeOffc 255.255.255.0 outside
pdm location outsideIP 255.255.255.0 outside
pdm location 10.0.0.22 255.255.255.255 outside
pdm logging warnings 100
pdm history enable
arp timeout 14400
global (outside) 1 interface
nat (inside) 0 access-list inside_outbound_nat0_acl
nat (inside) 1 0.0.0.0 0.0.0.0 0 0
access-group outside_access_in in interface outside
route outside 0.0.0.0 0.0.0.0 10.0.0.22 1
timeout xlate 3:00:00
timeout conn 1:00:00 half-closed 0:10:00 udp 0:02:00 rpc 0:10:00 h225 1:00:00
timeout h323 0:05:00 mgcp 0:05:00 sip 0:30:00 sip_media 0:02:00
timeout uauth 0:05:00 absolute
aaa-server TACACS+ protocol tacacs+
aaa-server RADIUS protocol radius
aaa-server LOCAL protocol local
http server enable
http outsideIP 255.255.255.0 outside
http HomeOffc 255.255.255.0 outside
http insideIP.0 255.255.255.255 inside
no snmp-server location
no snmp-server contact
snmp-server community public
no snmp-server enable traps
floodguard enable
sysopt connection permit-ipsec
crypto ipsec transform-set esp-3des-md5 esp-3des esp-sha-hmac
crypto map outside_map 20 ipsec-isakmp
crypto map outside_map 20 match address outside_cryptomap_20
crypto map outside_map 20 set peer outsideIP
crypto map outside_map 20 set transform-set esp-3des-md5
crypto map outside_map interface outside
isakmp enable outside
isakmp key Password address outsideIP netmask 255.255.255.255 no-xauth no-config-mode
isakmp key Password address outsideIP netmask 255.255.255.255 no-xauth no-config-mode
isakmp identity address
isakmp policy 20 authentication pre-share
isakmp policy 20 encryption 3des
isakmp policy 20 hash sha
isakmp policy 20 group 2
isakmp policy 20 lifetime 28800
telnet insideIP 255.255.255.0 inside
telnet timeout 5
ssh timeout 5
console timeout 0
dhcpd address insideIP range inside
dhcpd dns outside DNS IP
dhcpd lease 3600
dhcpd ping_timeout 750
dhcpd domain DomainName.com
dhcpd auto_config outside
dhcpd enable inside
terminal width 80
Any help is appreciated!
03-09-2004 08:32 AM
Can you ping a public IP from the PIX? Can you ping your Internet gateway from the pix (10.0.0.21)? If not, make sure that your router and the outside interface of the PIX have the proper speed and duplex settings.
03-09-2004 08:39 AM
Hi,
What error message do you get when you try to do nslookup from a inside PC? Also can you provide some syslog messages, do the following:
logging on
logging buffer debug
sh log
Can you post the above result.
Thanks - Jay
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide