07-16-2007 10:43 PM - edited 03-09-2019 06:23 PM
I want to put the asa5520 to the factory defoult please let me know how to do that. how to remove the configuration file from it.
please help me i am not able to do that. Thanks.
07-17-2007 01:02 AM
can anyone help me. i am still waiting
07-17-2007 01:21 AM
I`m not sure you can push this back to the factory default, however to completely remove the configuration, do the following:
Enable,
Conf t
write erase
Confirm the erase, and then reload the device via reload (do not save the configuration).
If the device has a CSC-SSM module, then theres a reset factory defaults on the menus of the module (type Session 1 from the ASA)
07-17-2007 03:55 AM
Hi,
To reset the ASA to factory defaults, do this:
conf t
clear configure all
wr
This should set the device to its original state; it should also preserve the default inspection policy.
12-14-2012 06:11 PM
Hi,
After do this procedure my ASA 5520 loose any thing and it´s not avaliable the option nameif and ip address in all interfaces.
I just have this option to set up in all interfaces:
ASA01(config)# interface gigabitEthernet 0/0
ASA01(config-if)# ?
Interface configuration commands:
default Set a command to its defaults
description Interface specific description
dhcp Configure parameters for DHCP client
duplex Configure duplex operation
exit Exit from interface configuration mode
flowcontrol Configure flowcontrol operation
help Interactive help for interface subcommands
no Negate a command or set its defaults
shutdown Shutdown the selected interface
speed Configure speed operation
ASA01(config-if)# no shut
The actual running-config is:
ASA01# sh run
: Saved
:
ASA Version 8.2(5)
!
hostname ASA01
domain-name test.com
enable password .... encrypted
no mac-address auto
!
interface GigabitEthernet0/0
duplex full
!
interface GigabitEthernet0/1
!
interface GigabitEthernet0/2
!
interface GigabitEthernet0/3
shutdown
!
interface Management0/0
!
class default
limit-resource All 0
limit-resource ASDM 5
limit-resource SSH 5
limit-resource Telnet 5
!
boot system disk0:/asa825-k8.bin
ftp mode passive
pager lines 24
no failover
asdm image disk0:/asdm-711.bin
no asdm history enable
arp timeout 14400
console timeout 0
admin-context admin
context admin
!
username cisco password xxxxxx encrypted privilege 15
prompt hostname context
no call-home reporting anonymous
call-home
profile CiscoTAC-1
no active
destination address http https://tools.cisco.com/its/service/oddce/services/DDCEService
destination address email callhome@cisco.com
destination transport-method http
subscribe-to-alert-group diagnostic
subscribe-to-alert-group environment
subscribe-to-alert-group inventory periodic monthly
subscribe-to-alert-group configuration periodic monthly
subscribe-to-alert-group telemetry periodic daily
Cryptochecksum:fd73f6597a4becb484c97b09f051636f
: end
Somebody what´s happens?
Thank´s.
12-15-2012 05:17 AM
Resolved... before of restore, this ASA was with HA enable. I just change it to mode single, reboot and it back to work normaly. The commands used was:
************************************
ASA01(config)# mode ?
configure mode commands/options:
multiple Multiple mode; mode with security contexts
noconfirm Do not prompt for confirmation
single Single mode; mode without security contexts
ASA01(config)# mode single
WARNING: This command will change the behavior of the device
WARNING: This command will initiate a Reboot
Proceed with change mode? [confirm]
Security context mode: single
***
*** --- SHUTDOWN NOW ---
...
ASA01(config)# int gi 0/0
ASA01(config-if)# ?
Interface configuration commands:
authentication authentication subcommands
ddns Configure dynamic DNS
default Set a command to its defaults
delay Specify interface throughput delay
description Interface specific description
dhcp Configure parameters for DHCP client
duplex Configure duplex operation
exit Exit from interface configuration mode
flowcontrol Configure flowcontrol operation
hello-interval Configures EIGRP-IPv4 hello interval
help Interactive help for interface subcommands
hold-time Configures EIGRP-IPv4 hold time
igmp IGMP interface commands
ip Configure ip addresses.
ipv6 IPv6 interface subcommands
mac-address Assign MAC address to interface
management-only Dedicate an interface to management. Block thru traffic
mfib Interface Specific MFIB Control
multicast Configure multicast routing
nameif Assign name to interface
no Negate a command or set its defaults
ospf Configure interface specific OSPF parameters
pim PIM interface commands
pppoe Configure parameters for PPPoE client
rip Configure interface specific RIP parameters
security-level Specify the security level of this interface after this
keyword, Eg: 0, 100 etc. The relative security level between
two interfaces determines the way the Adaptive Security
Algorithm is applied. A lower security_level interface is
outside relative to a higher level interface and equivalent
interfaces are outside to each other
shutdown Shutdown the selected interface
speed Configure speed operation
split-horizon Configures EIGRP-IPv4 split-horizon
summary-address Configures EIGRP-IPv4 summary-address
***************
Thanks!
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide