Hi,
I have a Nexus 5000 conected with a UCS C-200 with qlogic CNA in FCoE. The ethernet traffic is ok, but FC dont work fine, i thinks that i have configured all ok, by the show int vfc show the trunk vsan in initializating mode and i dont find what is the problem
switch(config-if)# sh int vfc 1
vfc1 is trunking
Bound interface is Ethernet1/9
Port description is Conexion FC con UCS1
Hardware is Virtual Fibre Channel
Port WWN is 20:00:00:0d:ec:e8:2c:7f
Admin port mode is F, trunk mode is on
snmp link state traps are enabled
Port mode is TF
Port vsan is 1
Trunk vsans (admin allowed and active) (1)
Trunk vsans (up) ()
Trunk vsans (isolated) ()
Trunk vsans (initializing) (1)
1 minute input rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
1 minute output rate 0 bits/sec, 0 bytes/sec, 0 frames/sec
0 frames input, 0 bytes
0 discards, 0 errors
0 frames output, 0 bytes
0 discards, 0 errors
last clearing of "show interface" counters never
Interface last changed at Mon Dec 20 19:59:31 2010
switch(config-if)# show port internal info interface vfc 1
vfc1 - if_index: 0x1E000000, phy_port_index: 0x1000
local_index: 0xffff
Admin Config - state(up), mode(F), speed(auto), trunk(on)
beacon(off), snmp trap(on), tem(false)
description(Conexion FC con UCS1)
port owner()
Operational Info - state(trunking), mode(TF), speed(auto), trunk(on)
state reason(None)
phy port enable (1), phy layer (FC), port_osm_mode(OSM)
participating(1), fcid(0x000000), bb_scn(0)
config port vsan (1), oper port vsan (1)
rx bb_credit(0), rx bb_credit multiplier(0)
rx bb_credit performance buffers(0), tx bb_credit(0)
not first time port bringup is 0
Port WWN is 20:00:00:0d:ec:e8:2c:7f
current state [PI_FSM_ST_TXPORT_INIT_TRUNKING_ENABLED]
port_init_eval_flag(0x00000401), cfg wait for none
FC_PORT_INIT_DATA_VALID (0)
FC_PORT_INIT_ADMIN_ST_DOWN_TO_UP (10)
FC_PORT_INIT_PHY_PORT_UP (49)
Mts node id 0x0
Lock Info: resource [vfc1]
type[0] p_gwrap[(nil)]
FREE @ 259535 usecs after Mon Dec 20 19:59:31 2010
type[1] p_gwrap[(nil)]
FREE @ 260559 usecs after Mon Dec 20 19:59:31 2010
type[2] p_gwrap[(nil)]
FREE @ 266012 usecs after Mon Dec 20 19:59:31 2010
0x10000001e000000
eport_init_flag(0x00000000), elp_chk_flag(0x00000000)
elp_rcvd_fc2_handle(0x00000000), elp_sent_fc2_handle(0x00000000)
esc_chk_flag(0x00000000), esc_fc2_handle(0x00000000)
elp_flags(0x0000), classes_supported(F), tx bb_credit(0)
Peer ELP Revision: 0
Timer active for PI_FSM_EV_TE_2_E_TIMER_EXPIRED
cnt_link_failure(0), cnt_link_success(0), cnt_port_up(0)
cnt_cfg_wait_timeout(2), cnt_port_cfg_failure(2), cnt_init_retry(0)
nos link failures (0), debounce window (300 ms), elp wait tout (750 ms)
link fail reason (0x0) num_elps_before_up (0)
internal_reinit_counter (0) external_reinit_counter (0)
Trunk Info -
trunk vsans (allowed active) (1)
trunk vsans (operational allowed) (1)
trunk vsans (up) ()
trunk vsans (isolated) ()
TE port per vsan information
vfc1, Vsan 1 - state(down), state reason(waiting for flogi), fcid(0x000000)
port init flag(0x0),
Lock Info: resource [vfc1, vsan 1]
type[0] p_gwrap[(nil)]
FREE @ 270103 usecs after Mon Dec 20 19:59:31 2010
type[1] p_gwrap[(nil)]
FREE @ 270104 usecs after Mon Dec 20 19:59:31 2010
type[2] p_gwrap[(nil)]
FREE @ 270105 usecs after Mon Dec 20 19:59:31 2010
0x40000011e000000
current state [TE_FSM_ST_WAIT_FOR_FLOGI]
RNID info not found.
first time elp: 1
Peer ELP Revision: 0
Pacer Info -
Pacer state: released credits due to timer expiry
PQP: not in progress
My configuration
vlan 701
fcoe vsan 1
name FCoE-Vsan1
interface vfc1
bind interface Ethernet1/9
switchport description Conexion FC con UCS1
no shutdown
interface Ethernet1/9
description Conexion FCoE con UCS1
switchport mode trunk
spanning-tree port type edge trunk
I need configure anything in UCS?.
Regards.
