Tag: "boot_issues" - Cisco Community

Latest Tagged

A Cisco 2600 or 3600 series router boots to ROMmon mode when a modem is attached to the console port - ( ‎06-22-2009 04:39 PM )

by on

0 Replies 2954 Views

0 Replies

2954 Views

Supervisor Engine module does not come online due to continuous booting loop, invalid boot variable,... - ( ‎06-22-2009 04:45 PM )

by on

0 Replies 2158 Views

0 Replies

2158 Views

ソフトウェアアップグレード後に Cisco Catalyst スイッチが ROMMON モード（「switch:」プロンプト）になる - ( ‎05-23-2011 07:20 PM )

by on

0 Replies 3233 Views

0 Replies

3233 Views

Cisco 2600, 3600, and 3700 series routers reload continuously - ( ‎06-22-2009 04:39 PM )

by on

0 Replies 1809 Views

0 Replies

1809 Views

Watchdog timeouts on 2600 and 3700 series routers with an AIM module. Router locks up upon bootup - ( ‎06-22-2009 05:05 PM )

by on

0 Replies 2442 Views

0 Replies

2442 Views

Router loads Cisco IOS after a tftpdnld command upgrade, yet no file is in Flash due to the -r switc... - ( ‎06-22-2009 04:09 PM )

by on

0 Replies 4197 Views

0 Replies

4197 Views

The 7200 series router fails to boot from Flash disk - ( ‎06-17-2009 10:20 PM )

by on

0 Replies 2042 Views

0 Replies

2042 Views

Continuous boot loop due to insufficient memory - ( ‎06-22-2009 04:08 PM )

by on

0 Replies 4301 Views

0 Replies

4301 Views

Router boots into boot mode without any errors displayed on the console - ( ‎06-22-2009 04:04 PM )

by on

0 Replies 22116 Views

0 Replies

22116 Views

The 2600, 3600 and 3700 series routers boot continuously after the Cisco IOS Software upgrade due to... - ( ‎06-22-2009 03:42 PM )

by on

0 Replies 2540 Views

0 Replies

2540 Views

Top Tagged

A router produces error messages followed by the %SYS-6-BOOT_MESSAGES: Messages above this line are ... - ( ‎06-22-2009 06:14 PM )

by on

0 Replies 3852 Views

0 Replies

3852 Views

During MSFC bootup, the "%SYS-6-READ_BOOTFILE_FAIL" error message appears in Catalyst 6500 series sw... - ( ‎06-22-2009 06:13 PM )

by on

0 Replies 3240 Views

0 Replies

3240 Views

Supervisor Engine 720 crashes while it tries to bootup in a Cisco Catalyst 6500 Series switch runnin... - ( ‎06-22-2009 06:10 PM )

by on

0 Replies 1704 Views

0 Replies

1704 Views

The boot loader does not appear in the output of the "show version" command, although the output of ... - ( ‎06-22-2009 05:39 PM )

by on

0 Replies 1174 Views

0 Replies

1174 Views

Cisco Catalyst switch in ROMMON mode ("switch:" prompt) after a software upgrade - ( ‎06-22-2009 05:37 PM )

by on Latest post on by

2 Replies 79090 Views

2 Replies

79090 Views

A Novell IPX workstation does not have the Novell Login Screen at bootup due to spanning tree delays - ( ‎06-22-2009 05:35 PM )

by on

0 Replies 1113 Views

0 Replies

1113 Views

A new image takes time to load in Catalyst 6000/6500 Series Switches after a software upgrade - ( ‎06-22-2009 05:35 PM )

by on

0 Replies 871 Views

0 Replies

871 Views

How to convert the router from normal execution mode to ROMMON mode - ( ‎06-22-2009 05:34 PM )

by on

0 Replies 2993 Views

0 Replies

2993 Views

Card in a modular Catalyst 4000, 5000 or 6000 series chassis does not function properly or is not on... - ( ‎06-22-2009 05:33 PM )

by on

0 Replies 2904 Views

0 Replies

2904 Views

The router reports the device does not contain a valid magic number error message and fails to load ... - ( ‎06-22-2009 03:38 PM )

by on

0 Replies 7162 Views

0 Replies

7162 Views

Top Taggers

User

Count