03-03-2011 10:13 AM - edited 03-20-2019 07:33 PM
There are several Visio stencils that are missing from the library that I need. They're important to me (and I imagine others want them too) as I need to do rack elevation diagrams. I hate to open a TAC case on them but not sure what else to do. Any thoughts?
The stencils I require are:
ASA5510 (Rear view - the side with the interfaces)
ME-C6524GT-8S (Rear view - the side with the power supplies) - 24 Ethernet - 10/100/1000 interfaces + 8 Gigabit Ethernet SFP uplinks, 1 fan tray
PWR-400W-AC - 400W AC power supply for the Cisco ME 6524
PWR-400W-DC - 400W DC power supply for the Cisco ME 6524
ME-C3750-24TE-M (Rear View - the side with the power supplies) - Cisco Catalyst 3750 Metro
PWR-ME3750-AC - Cisco Catalyst 3750 Metro Switch Primary AC power supply
PWR-ME3750-DC - Cisco Catalyst 3750 Metro Switch Primary AC power supply
Cheers
Solved! Go to Solution.
08-01-2012 08:01 AM
Any word on getting the 1900 stencils?
08-02-2012 10:50 AM
Hi Brandon,
They were interested in moving ahead with this a couple of months ago and then it seemed to have fallen off the priority list. I've just sent another request to the 1900 product group about this. Sorry about the delay in getting an answer.
Regards,
Brett Newman
Cisco Visio Production
Visimation Inc.
03-12-2012 02:30 PM
Hi Gary,
So far I haven't been successful in identifying a person in the UC product group to work with me on this. I'll keep trying and I apologize for the delay in getting you a response.
Regards,
Brett Newman
Cisco Visio Production
Visimation Inc.
04-04-2012 03:39 AM
I am in need of an ACS appliance physical product stencil, product reference: CSACS-1121-K9.
I have never seen any ACS physical product icon, but if anyone can point me in the direction of one, or one that looks very similar that would be very handy. Otherwise it would be a request to Visimation again.
thanks
04-09-2012 01:34 PM
Hi Nicholas,
Sorry about the slow response... I was on the road most of last week.
The CSACS-1121-K9 is almost identical to the ISE 3315 which is on the Security-ISE stencil that you can download from the Cisco Visio stencil page:
http://www.cisco.com/en/US/products/hw/prod_cat_visios.html
Regards,
Brett Newman
Cisco Visio Production
Visimation Inc.
04-10-2012 10:21 AM
Brett,
Have you had any luck with either the Catalyst 6503 stencils or the UC500 stencils?
Cheers
04-10-2012 04:11 PM
Hi Gary,
I'm working with both product groups to get production approval but no green lights yet... I'm sorry about that.
Regards,
Brett Newman
Cisco Visio Production
Visimation Inc.
06-02-2012 01:55 AM
Brett,
Any luck on the UC500 or 6503 stencils? Have they given you a no or just not given you a yes?
Cheers
06-12-2012 03:24 PM
Hi Gary,
I did not receive a response from my last email at the end of March so I just tried again. Sorry about this but it's pretty common since the product managers have a lot to do and they typically don't know anything about the process of getting Visio images created until I contact them about it.
Regards,
Brett Newman
Cisco Visio Production
Visimation Inc.
06-13-2012 12:20 PM
Hi Gary,
Unfortunately, I just received a "no" from the UC500 product group. However, I'm expecting to discuss this with the 6500 product group next week.
Regards,
Brett Newman
Cisco Visio Production
Visimation Inc.
08-07-2012 03:53 PM
Brett,
Did anything come out of your discussion with the 6500 product group?
Sent from Cisco Technical Support iPhone App
08-13-2012 11:00 AM
Hi Gary,
Sorry for the slow response. This is my first chance to log in here in about a week.
Yes, we are nearing completion of a 6500 stencil update. We are waiting for some missing photos from the product group to complete the set so it should be imminent. I can't be more specific than that, but it will be soon.
Regards,
Brett Newman
Cisco Visio Production
Visimation Inc.
08-28-2012 07:34 AM
Brett I see the new 6503-E stencil has been posted as of the 21st, but I don't see a rear view. Is it going to be forthcoming (along with associated power supplies, etc) or are we limited to the front view?
Thanks!
08-29-2012 04:48 PM
Hi Gary,
I requested funding for the rear views but the product group approved only the front views. If you would like to post a justification I will forward it to them to see if they will reconsider. Customer input is always taken seriously and I can be more effective with that kind of backup from the field.
Regards,
Brett Newman
Cisco Visio Production
Visimation Inc.
08-29-2012 05:14 PM
Brett,
First, thank-you for all your efforts. It means a lot to me (and I'm sure a lot of other people).
On the topic of rear views, they approved creation of rear views of nearly all their other products, what makes this one different? I can't be the only guy that documents the back side of his racks. It's especially pertinent because there are multiple configurations of power supplies on this particular model.
I've had an offer from another skilled visio stencil creator to create the rear view if there's a high quality photo of the rear of the switch to be found. Unfortunately I can't provide one right now, but if you happen to have one then I can get him to create it to satisfy at least my need. Unfortunately that doesn't help the people who will come to the Cisco stencil page looking for the same.
On another note, did anything ever come of your discussion to have them order stencils as part of the pre-release process (along with product photos)? I think this would simplify a lot and surely cut down on the massive amounts of justification that must be done to have these stencils created.
Discover and save your favorite ideas. Come back to expert answers, step-by-step guides, recent topics, and more.
New here? Get started with these tips. How to use Community New member guide