Turn on suggestions
Auto-suggest helps you quickly narrow down your search results by suggesting possible matches as you type.
Showing results for
- Cisco Community
- :
- About owillins
Stats
Member since
03-03-2003
1422
Posts
233
Helpful
32
Solutions
10-15-2009
10:00 AM
This RFC 2544 specific set of tests that vendors can use to measure and report the performance characteristics of network devices. The results of these tests will provide the user comparable data from different vendors with which to evaluate these devices. I think it will give more over 99% results.
... View more
Created by
owillins
in Storage Networking
in Storage Networking
09-10-2009
06:59 AM
09-10-2009
06:59 AM
If you get yellow text 'No Traps' in FM client means that the FM has not registered trap address on this switch successfully and hence not receiving traps from those switches. It may be that the trap address table is full (max is 10 entries) on the switch. If table is full, then delete any stale/unused addresses in the switch. The FMS's next periodic poll will add it's trap address to the switch and the 'No Traps' warning will go away after this. Try refreshing the Switch table in the FM client to see an updated status. And also check the Switches remain manageable even when "No Traps" is displayed. Then you are hitting bug CSCta72679. To workaround this Rediscovering the Fabric will change the status back to "ok" but this is only a temporary solution.
... View more
08-28-2009
09:20 AM
I understand the box is stuck in a loop and will not complete the boot up process. It looks like the RAID controller physical cache has failed which is what would have caused your raid failure on the CM for this unit.
... View more
Re: DOT1X-3-USER_LOGIN_DENY: Authentica...
in Wireless and Mobility
08-28-2009
06:20 AM
08-28-2009
06:20 AM
This error message says user authentication failed. The most likely cause is that the user name is already in use by another client. So please ensure that unique user names are used by each client.
... View more
08-25-2009
01:47 PM
HA is not supported on AP1000 series. All other Access Points support HA.
... View more
08-19-2009
09:38 AM
It is not freeware. But you can download demo. Cisco and NetQoS partnered to deliver the visibility and control you need to optimize business-critical applications for performance. The NetQoS Performance Center provides the most comprehensive performance monitoring solution available for next-generation Cisco optimization technologies, including the Cisco Application Control Engine (ACE) Module. • Accurately quantify server response time and session load balancing • Visualize Cisco ACE performance statistics, utilization trends, layer 4 and 7 connection diagnostics, error analysis, and availability • Justify investments in new content delivery hardware and other data center systems • Accurately size and configure new infrastructure deployments in the data center • Maintain visibility to troubleshoot performance issues in multi-tier server environments NetVoyant uses SNMP management information bases (MIBs) to define the types of data to be collected. Users can view the MIBs to create event notifications or assist in other administrative tasks, and can compile new MIBs to add functionality to NetVoyant. NetVoyant creates events and alarms to alert users to issues with NetVoyant services, missed SNMP polls, exceeded utilization, and other configurable thresholds. Administrators can set thresholds, create notifications that NetVoyant triggers in response to events, and view event and alarm logs.
... View more
08-18-2009
08:43 AM
To initiate a ping and only then the IPSec SA between inside hosts would be created. Please makesure you are hitting this bug CSCsu58733 L2TP IPSec ASA send ESP packet with using old SA pair.
... View more
Created by
owillins
in Policy and Access
in Policy and Access
08-17-2009
11:32 AM
08-17-2009
11:32 AM
We are going to set up a CAR server as a Radius proxy. Looking through the admin guide, it mainly mention how to set up CAR as a RADIUS server instead of a proxy server. We still have no idea on how to configure it. Could you help to advice some guidelines for the basic setup for the Radius proxy Answer CAR's operation and configuration is based on a set of objects. The objects you use to configure and operate your Cisco Access Registrar 4.1 RADIUS server. http://www.cisco.com/en/US/docs/net_mgmt/access_registrar/4.2/user/guide/objects.html#wp1041338
... View more
08-17-2009
10:22 AM
Each PC or network device that uses TCP/IP must have a unique address to identify itself in a network. If the IP address is not unique to a network, Windows will generate an IP conflict error message. You can assign a static IP address to a PC. I hope this might be cause of your issue. Here is the user guide. ftp://ftp.linksys.com/downloads/NA/userguide/RVS4000_V10_UG_B8731-web.pdf
... View more
08-07-2009
12:56 PM
Try to assign static IP address. You can verify which IP address was assigned to the Cisco ATA with the IVR menu. The Dynamic Host Configuration Protocol (DHCP) server is enabled by default from version 2.x and later. When the DHCP field is set to 1, the Cisco ATA 186 contacts the DHCP server to get the IP address, subnet mask, and default route. http://www.cisco.com/en/US/products/hw/gatecont/ps514/products_configuration_example09186a00800c3a50.shtml#task1
... View more
Created by
owillins
in Security Management
in Security Management
07-15-2009
07:43 AM
07-15-2009
07:43 AM
I don't think this is possible
... View more
Created by
owillins
in VPN and AnyConnect
in VPN and AnyConnect
07-14-2009
09:16 AM
07-14-2009
09:16 AM
If the AAA server authenticates the user, the FWSM displays the User Accepted text, if specified, to the user; otherwise it displays the User Rejected text, if specified. If the rejection is because of invalid credentials (such as an incorrect username) or because the password expired, the Invalid Credentials or Expired Password text shows, instead of the User Rejected text.
... View more
Created by
owillins
in Other Security Subjects
in Other Security Subjects
07-13-2009
12:55 PM
07-13-2009
12:55 PM
This error message states the access list check failed; either it matched a deny, or it matched nothing, such as an implicit deny. Connection denied by user access list acl_ID, which was defined per the AAA authorization policy on CiscoSecure ACS. This message works only with RADIUS protocol.
... View more
Created by
owillins
in Other Security Subjects
in Other Security Subjects
07-01-2009
03:00 PM
07-01-2009
03:00 PM
Devices may be all in one or distributed sites. if the devices are in one sites or the cost of transferring the data between sites is low then one CS- MARS appliance may be able to handle the job. Sites may belong to separate administrative units where smaller boxes that each administrative unit could own may be a better solution than one larger, shared CS-MARS. Begin with the number of events per day. If the traffic is uniform throughout the day the convert the events per day directly into events per second. Calculate Estimated Number of Events Per Second. Events/hours = Events/day * 1 day / 24 hours Events/second = Events/hours * 1 hours/3600 second For example, assume 5 000 000 Events/day Events/second ~= 58
... View more
Created by
owillins
in Wireless Security and Network Management
in Wireless Security and Network Management
07-01-2009
02:47 PM
07-01-2009
02:47 PM
Simply wants to manage bridges (e.g. alarms, statistics, config & firmware management), the WLSE can do that. An integrated wired and wireless Intrusion Detection System (IDS) on 1400. The 1400 does not support the centralized solution However, note that there is no IDS or Radio management with WLSE + 1400.
... View more
10-15-2009
This RFC 2544 specific set of tests that vendors can use to measure and
report the performance chara...
Created by
owillins
in Storage Networking
09-10-2009
09-10-2009
If you get yellow text 'No Traps' in FM client means that the FM has not
registered trap address on ...
08-28-2009
I understand the box is stuck in a loop and will not complete the boot
up process.It looks like the ...
Created by
owillins
in Wireless and Mobility
08-28-2009
08-28-2009
This error message says user authentication failed. The most likely
cause is that the user name is a...
08-18-2009
To initiate a ping and only then the IPSec SA between inside hosts would
be created.Please makesure ...
Created by
owillins
in Policy and Access
08-17-2009
08-17-2009
We are going to set up a CAR server as a Radius proxy. Looking through
the admin guide, it mainly me...
08-17-2009
Each PC or network device that uses TCP/IP must have a unique address to
identify itself in a networ...
08-07-2009
Try to assign static IP address. You can verify which IP address was
assigned to the Cisco ATA with ...
Created by
owillins
in VPN and AnyConnect
07-14-2009
07-14-2009
If the AAA server authenticates the user, the FWSM displays the User
Accepted text, if specified, to...
07-13-2009
This error message states the access list check failed; either it
matched a deny, or it matched noth...
07-09-2009
Call Manager Express does not support video services and I am not aware
of any plans to introduce vi...
Public Statistics
| Date Registered | 03-03-2003 09:50 AM |
| Date Last Visited | 08-18-2017 03:50 AM |
| Total Messages Posted | 1,422 |
| Total Helpful Votes Received | 233 |
