About Hilal Computers

Hilal Computers · 08-09-2012

Hi all,I have a customer who is facing caller-id issue in the fxo port. Call flow as follow, PSTN---> FXO---->H323---->CUCM. Customer located in saudi arabia(where caller id standard is ETSI-DTMF).I have tried to configure the voice port as below,voi...

Hilal Computers · 07-13-2012

Dear All,I have an intermittent DTMF issue with one of my auto attendant message. Sometimes DTMF is passing through and reaching the extension numbers and other times its not passing. ISP--> FXO--> CUEAs mentioned above, calls reaching to analog line...

Hilal Computers · 05-13-2012

Hi all,I have a requirement to configure 2 different AA messages for different analog lines? How do we do this? I'm new to cme based IVR.Regardskajen

Hilal Computers · 05-13-2012

Hi all,I'm having couple of issues with the analog trunks. 1. Calls getting disconnected after one ring when we dial outside ( This is happening only intermittently)2. Although customer has six analog lines, they coudn't dial outside after 2nd call (...

Hilal Computers · 05-04-2012

Dear All,I have a scenario where, I have created two VLANS (Server - 172.21.1.0/24 and client 172.21.2.0/24) in L3 switch. Intervlan routing enabled. Everything working perfectly.I have a strange issue, One PC which has 172.21.1.10 IP address connect...

Hilal Computers · 08-13-2012

Hi Paolo,Thanks for the reply. Can you list some possibility of causes the AA message is not picking up from FXO? This is really weired. I have changed every possible options in the voice port, still i don't see any luck. When i change the caller-id ...

Hilal Computers · 08-13-2012

I have been troubleshooting this issue for a long time now. and whenever i configure the caller-id alerting to dsp, am getting the same error with "not EFXS 2"...Find the configuration for application and voice-port below. Debug vpm signal for this c...

Hilal Computers · 08-12-2012

Now the issue is little bit different. When i configure the voice port to reach aa-pilot , i can only hear some tone(not the aa message). I can see the called id received in fxo port but audio prompt not playing. But when i configure voice port with ...

Hilal Computers · 08-12-2012

By the way , below error am facing when i debug the call which directed to auto attendant..htsp_process_event: [0/1/2, FXOLS_PROCEEDING, E_HTSP_ALERT]fxols_offhook_alerthtsp_call_service_msghtsp_call_service_msg not EFXS (2)htsp_call_service_msghtsp_...

Hilal Computers · 08-12-2012

Thanks for the reply Paolo.I tried to upgrade the IOS of the gateway and configure the voice port with "caller-id alerting dsp-pre-alloc".. After that caller ID started to work for direct IP phones. But i wanted to route this FXO port through the Aut...

Member Since	‎05-03-2012 02:46 AM
Date Last Visited	‎01-12-2024 12:06 AM
Posts	17

User Statistics

User Activity

Cisco 3800 FXO ports with caller-id issue.

Intermittent DTMF issue with CME Autoattendant message

CME multiple Auto Attendant config for different analog lines

Cisco CME FXO issue with outgoing calls

Dial-up connection disconnects the LAN network

Cisco 3800 FXO ports with caller-id issue.

Cisco 3800 FXO ports with caller-id issue.

Cisco 3800 FXO ports with caller-id issue.

Cisco 3800 FXO ports with caller-id issue.

Cisco 3800 FXO ports with caller-id issue.