Hi, we have two 6509 in VSS with STP configured. from each 6509 there is a link to service provider but to different office(equipment) of provider. one link is designated forwarding, another link is designated blocking. when i shut down the first interface, then second interface becomes designated forwarding, but when active 6509 is powered off then second interface doesn't become forwarding, it is stil stays in blocking mode. second 6509 became active also, but only link to provider not became forwarding. is this normal? ... View more

Hi, I have s72033-advipservicesk9_wan-mz.122-33.SXH8b.bin image, and I want to know if this image support VSS with two superviser engine 720-10G  on both catalyst6509 ? Thanks in advance ... View more

Hi, we have two 6509 catalyst. we bought two new SFM-capable 16 port 1000mb GBIC/WS-X6516A-GBIC module. but our catalysts doesnt support them. we don't know the reason. we tried on another 6500 series catalyst they worked. here are the outputs from our 6509: Core-SW-1#sh module Mod Ports Card Type                              Model              Serial No. --- ----- -------------------------------------- ------------------ -----------   1    0  1-subslot SPA Interface Processor-600  7600-SIP-600       JAE14090958   2   48  CEF720 48 port 10/100/1000mb Ethernet  WS-X6748-GE-TX     SAL1413DX2B   3   16  CEF720 16 port 10GE                    WS-X6716-10GE      SAL1414EL2Q   4    1  Application Control Engine Module      ACE20-MOD-K9       SAD1408036Z   5    5  Supervisor Engine 720 10GE (Active)    VS-S720-10G        SAL1414ERDT   6    5  Supervisor Engine 720 10GE (RPR-Warm)  VS-S720-10G        SAL1414ERE3   7   16  CEF720 16 port 10GE                    WS-X6716-10GE      SAL1414ER93   8   16  SFM-capable 16 port 1000mb GBIC        WS-X6516A-GBIC     SAL1326SVBS Mod MAC addresses                       Hw    Fw           Sw           Status --- ---------------------------------- ------ ------------ ------------ -------   1  68ef.bd43.20c0 to 68ef.bd43.20ff   1.3   Unknown      Unknown      PwrDown   2  68ef.bd73.d3b0 to 68ef.bd73.d3df   3.4   12.2(18r)S1  12.2(33)SXI6 Ok   3  c47d.4f8f.ffe0 to c47d.4f8f.ffef   1.1   12.2(18r)S1  12.2(33)SXI6 Ok   4  0026.cb89.6b00 to 0026.cb89.6b07   2.6   8.7(0.22)ACE A2(1.6a)     Ok   5  001e.4a7e.fb60 to 001e.4a7e.fb67   3.2   8.5(3)       12.2(33)SXI6 Ok   6  0026.cb61.13e0 to 0026.cb61.13e7   3.2   8.5(3)       12.2(33)SXI6 Ok   7  8843.e1d0.ab80 to 8843.e1d0.ab8f   1.1   12.2(18r)S1  12.2(33)SXI6 Ok   8  0026.0b7d.aec8 to 0026.0b7d.aed7   4.7   Unknown      12.2(33)SXI6 PwrDown Mod  Sub-Module                  Model              Serial       Hw     Status ---- --------------------------- ------------------ ----------- ------- -------   1  SIP Distributed Forwarding  7600-SIP-600-DC    JAE14090967  1.1    PwrDown   2  Distributed Forwarding Card WS-F6700-DFC3CXL   SAL1414EFNQ  1.6    Ok   3  Distributed Forwarding Card WS-F6700-DFC3CXL   SAL1414EL5J  1.6    Ok   5  Policy Feature Card 3       VS-F6K-PFC3CXL     SAL1414EFCT  1.2    Ok   5  MSFC3 Daughterboard         VS-F6K-MSFC3       SAL1414EW4T  2.1    Ok   6  Policy Feature Card 3       VS-F6K-PFC3CXL     SAL1414EFEL  1.2    Ok   7  Distributed Forwarding Card WS-F6700-DFC3CXL   SAL1414EF3K  1.6    Ok Mod  Online Diag Status ---- -------------------   1  Not Applicable   2  Pass   3  Pass   4  Pass   5  Pass   6  Pass   7  Pass   8  Not Applicable the module is in slot 8 Core-SW-1#sh power system power redundancy mode = redundant system power total =     5771.64 Watts (137.42 Amps @ 42V) system power used =      2523.36 Watts (60.08 Amps @ 42V) system power available = 3248.28 Watts (77.34 Amps @ 42V)                         Power-Capacity PS-Fan Output Oper PS   Type               Watts   A @42V Status Status State ---- ------------------ ------- ------ ------ ------ ----- 1    WS-CAC-6000W       5771.64 137.42 OK     OK     on 2    WS-CAC-6000W       5771.64 137.42 OK     OK     on                         Pwr-Allocated  Oper Fan  Type               Watts   A @42V State ---- ------------------ ------- ------ ----- 1    WS-C6509-E-FAN      210.00  5.00  OK                         Pwr-Requested  Pwr-Allocated  Admin Oper Slot Card-Type          Watts   A @42V Watts   A @42V State State ---- ------------------ ------- ------ ------- ------ ----- ----- 1    7600-SIP-600        341.88  8.14     -     -     on    off (DFC mismatch) 2    WS-X6748-GE-TX      392.70  9.35   392.70  9.35  on    on 3    WS-X6716-10GE       487.20 11.60   487.20 11.60  on    on 4    ACE20-MOD-K9        219.66  5.23   219.66  5.23  on    on 5    VS-S720-10G         363.30  8.65   363.30  8.65  on    on 6    VS-S720-10G         363.30  8.65   363.30  8.65  on    on 7    WS-X6716-10GE       487.20 11.60   487.20 11.60  on    on 8    WS-X6516A-GBIC      152.04  3.62     -     -     on    off (not supported) system auxiliary power mode = off system auxiliary power redundancy operationally = non-redundant system primary connector power limit =   10920.00 Watts (260.00 Amps @ 42V) system auxiliary connector power limit = 10500.00 Watts (250.00 Amps @ 42V) system primary power used =              2523.36 Watts (60.08 Amps @ 42V) system auxiliary power used =            0 Watt Core-SW-1#sh module switch 1 slot 8 Switch Number:     1   Role:   Virtual Switch Active ----------------------  ----------------------------- Mod Ports Card Type                              Model              Serial No. --- ----- -------------------------------------- ------------------ -----------   8   16  SFM-capable 16 port 1000mb GBIC        WS-X6516A-GBIC     SAL1326SVBS Mod MAC addresses                       Hw    Fw           Sw           Status --- ---------------------------------- ------ ------------ ------------ -------   8  0026.0b7d.aec8 to 0026.0b7d.aed7   4.7   Unknown      12.2(33)SXI6 PwrDown Mod  Online Diag Status ---- -------------------   8  Not Applicable can anybody help us with this problem? ... View more

Hi, i have a question. i have a server statically nated to one outside ip. can my inside users access this external ip from inside subnet? for example server 10.1.1.1 nated to 85.x.x.x can my internal user from 10.2.2.0 subnet access 85.x.x.x ip if he write this ip in browser ? if yes what should i do allow this? because in my situation internal users couldn't access this server by external ip. ... View more

Hi we have core switch in our network connected to ASA on switch ve have vlans: vlan 20 inside   ip address 172.20.20.0 vlan 30 dmz     ip address 172.30.30.0 interface vlan 20 ip address 172.20.20.254 interface vlan 30 ip address 172.30.30.254 ip route 0.0.0.0 0.0.0.0 172.20.20.1 on ASA: int g0/0 nameif inside ip add 172.20.20.1 int g0/1 nameif dmz ip add 172.30.30.1 we want traffic between inside and dmz pass through ASA on servers in dmz gateway is 172.30.30.1 the ip address of ASA on inside vlan pc's gateway is 172.20.20.254 the ip address of core we did static ( inside,dmz) 172.20.20.0 172.20.20.0 netmask 255.255.255.0 the we tried static (dmz,inside) 172.20.20.0 172.30.30.0 netmask 255.255.255.0 but it didn't help please advice how to configure,and pass traffic between inside and dmz through ASA? ... View more