About masyamad

masyamad · 05-05-2019

Hi ISE dev/doc team, My customer is considering ISE node failover operation during each node failure so evaluating the functional impact on each failure. Now admin guide shows secondary MnT is 'read-only', but we haven't fully understood the actua...

masyamad · 12-16-2018

Hi dev team, AFAIK when I enabled debug by cli command (like debug backuprestore 7), the debug log will be recorded in ADE.log on ACS. But on ISE, ADE.log doesn't have any debug output even with debug all. I tested ISE2.3 and 2.4 then got same resu...

masyamad · 12-11-2018

When I swap MnT primary/secondary in 2 nodes deployment, usually use role dropdown in deployment nodes menu as follows. But I notice the operation is not documented in administration guide. https://www.cisco.com/c/en/us/td/docs/security/ise/2-4/ad...

masyamad · 10-12-2018

Sorry for the quick question. But now I can't find ISE command to check interface link status. For example, now eth1(gigabitEthernet 1) stays admin:up, link status:down C:\>snmpwalk -c ro -v 2c 192.168.10.1 1.3.6.1.2.1.2.2.1.2.3IF-MIB::ifDescr.3 = ...

masyamad · 10-04-2018

Hi dev team, I found following critical messages about secure boot in CIMC SEL. * It occured on brand-new SNS-3595 without any upgrading/downgrading CIMC. ISE-CIMC /sel # show entries<...snipped...> 2018-10-05 02:07:54 Critical "System Sof...

masyamad · 05-29-2019

Hi Nidhi, Thanks for looking into this issue. I just wanted to know if there are any updates on this since the customer requested an update from Cisco.

masyamad · 05-16-2019

Hi, <Remove some statement because above response about ALARM from Nidhi is updated> BTW could you tell me the ALARM implementation. > SMnT detects that the node has been down based on the syslogs and starts triggering the alarm. Does "triggeri...

masyamad · 05-10-2019

Thanks for the clarification! > - Alarms are generated only from PMnT . So if PMnT goes down, you will not get the alarms until the node is down or you promote the SMnT node. Thanks. But in my lab testing, Home page still show some ALARMS during PMnT...

masyamad · 05-06-2019

Hi Nidhi, I might mis-understood your explanation. Let me explain my question again. > For any report generation , PAN queries Primary MnT node for data. For session related queries as well, the request is > made to the Primary MnT node only. Af...

masyamad · 05-06-2019

Hi Nidhi,Thanks for the update. Regarding report generation, admin guide says secondary MnT run instead of Primary.https://www.cisco.com/c/en/us/td/docs/security/ise/2-4/admin_guide/b_ise_admin_guide_24/b_ise_admin_guide_24_new_chapter_011111.html?bo...

Member Since	‎06-02-2010 06:43 PM
Date Last Visited	‎06-11-2024 01:03 AM
Posts	95
Total Helpful Votes Received	18

User Statistics

User Activity

Functional diffs between primary/secondary MnT

ISE CLI Debug output

Change MnT Role

Link status command on ISE2.4

ISE/SNS-3595 EFI Secure Boot errors after booting up

Re: Functional diffs between primary/secondary MnT

Re: Functional diffs between primary/secondary MnT

Re: Functional diffs between primary/secondary MnT

Re: Functional diffs between primary/secondary MnT

Re: Functional diffs between primary/secondary MnT